28 August 2013 in IEEE Transactions on Vehicular Technology
This paper deals with the lateral motion control of four-wheel-independent-drive electric vehicles (4WID-EVs) subject to onboard network-induced time delays. It is well known that the in-vehicle network and x-by-wire technologies have considerable advantages over the traditional point-to-point communication. However, on the other hand, these technologies would also induce the probability of time-varying delays, which would degrade control performance or even deteriorate the system. To enjoy the advantages and deal with in-vehicle network delays, an H∞-based delay-tolerant linear quadratic regulator (LQR) control method is proposed in this paper. The problem is described in the form of an augmented discrete-time model with uncertain elements determined by the delays. Delay uncertainties are expressed in the form of a polytope using Taylor series expansion. To achieve a good steady-state response, a generalized proportional-integral control approach is adopted. The feedback gains can be obtained by solving a sequence of linear matrix inequalities (LMIs). Cosimulations with Simulink and CarSim demonstrate the effectiveness of the proposed controller. Comparison with a conventional LQR controller is also carried out to illustrate the strength of explicitly dealing with in-vehicle network delays.
12 January 2015 in IEEE Transactions on Vehicular Technology
In this paper, we investigate the combined active front-wheel steering/direct yaw-moment control for the improvement of vehicle lateral stability and vehicle handling performance. A more practical assumption in this work is that the longitudinal velocity is not constant but varying within a range. Both the nonlinear tire model and the variation of longitudinal velocity are considered in vehicle system modeling. A linear-parameter-varying model with norm-bounded uncertainties is obtained. To track the system reference, a generalized proportional-integral (PI) control law is proposed. Since it is difficult to get the analytic solution for the PI gains, an augmented system is developed, and the PI control is then converted into the state-feedback control for the augmented system. Both the stability and the energy-to-peak performance of the augmented system are explored. Based on the analysis results, the controller-gain tuning method is proposed. The proposed control law and controller design method are illustrated via an electric vehicle model.
11 February 2014 in Vehicle System Dynamics
In this paper, we investigate the vehicle lateral dynamics stabilisation problem to enhance vehicle handling by considering time-varying longitudinal velocity. The longitudinal velocity is described by a polytope with finite vertices and a novel technique is proposed to reduce the number of vertices. Since the tyre dynamics is nonlinear, the cornering stiffness is represented via the norm-bounded uncertainty. Concerning the time-varying velocity and the nonlinear tyre model, a linear parameter-varying vehicle model is obtained. As the velocity and the states are measurable, a gain-scheduling state-feedback controller is introduced. In the lateral control, the sideslip angle is required to be as small as possible and the yaw rate is constrained to a certain level. Thus, the control objective is to minimise the sideslip angle while the yaw rate is under a prescribed level or constrain both the sideslip angle and the yaw rate to prescribed levels. To consider the transient response of the closed-loop system, the -stability is also employed in the energy-to-peak control. The optimal controller can be obtained by solving a set of linear matrix inequalities. A nonlinear vehicle model is utilised to illustrate the design procedure and the effectiveness of the proposed design method. Finally, simulations and comparisons are carried out to show the significant advantage of the designed controller. Compared to the open-loop system, the closed-loop system with the designed controller can achieve much smaller sideslip angle and the yaw rate is closer to the desired yaw rate from a reference model. Therefore, the vehicle safety and the handling are both improved in our simulation cases.
1 April 2011 in Journal of Power Sources
18 March 2015 in IEEE Transactions on Control Systems Technology
The energy efficiency of parallel hybrid electric vehicles (HEVs) can degrade significantly when the battery state-of-charge (SoC) reaches its boundaries. The road grade has a great influence on the HEV battery charging and discharging processes, and therefore the HEV energy management can be benefited from the road grade preview. In real-world driving, the road grade ahead can be considered as a random variable because the future route is not always available to the HEV controller. This brief proposes a stochastic model predictive control-based energy management strategy using the vehicle location, traveling direction, and terrain information of the area for HEVs running in hilly regions with light traffic. The strategy does not require a determined route being known in advance. The road grade is modeled as a Markov chain and stochastic HEV fuel consumption and battery SoC models are developed. The HEV energy management problem is formulated as a finite-horizon Markov decision process and solved using stochastic dynamic programming. The proposed method is evaluated in simulation and compared with an equivalent consumption minimization strategy and the dynamic programming results. It is shown that the developed method can help maintaining the battery SoC within its boundaries and achieve good energy consumption performance.
27 March 2009 in IEEE Transactions on Control Systems Technology
A coordinated reconfigurable vehicle dynamics control (CRVDC) system is achieved by high-level control of generalized forces/moment, distributed to the slip and slip angle of each tire by an innovative control allocation (CA) scheme. Utilizing control of individual tire slip and slip angles helps resolve the inherent tire force nonlinear constraints that otherwise may make the system more complex and computationally expensive. This in turn enables a real-time adaptable, computationally efficient accelerated fixed-point (AFP) method to improve the CA convergence rate when actuation saturates. Evaluation of the overall system is accomplished by simulation testing with a full-vehicle CarSim model under various adverse driving conditions, including scenarios where vehicle actuator failures occur. Comparison with several other vehicle control system approaches shows how the system operational envelope for CRVDC is significantly expanded in terms of vehicle global trajectory and planar motion responses.