1 January 2018 in Geophysics
Previous studies found a significant increase of acoustic velocities between seismic and ultrasonic frequencies (seismic dispersion) for shales, which would have to be taken into account when comparing seismic or sonic field data with ultrasonic measurements in the laboratory. We have executed a series of experiments performed with a partially saturated Mancos shale and a Pierre shale I in which the influence of water saturation on acoustic velocities and seismic dispersion was investigated. The experiments were carried out in a triaxial setup allowing for combined measurements of quasistatic rock deformation, ultrasonic velocities, and dynamic elastic stiffness at seismic frequencies under deviatoric stresses. Prior to testing, the rock samples were preconditioned in desiccators at different relative humidities. For both shale types, we present and analyze the experimental results that demonstrate strong saturation and frequency dependence of dynamic Young’s moduli, Poisson’s ratios, and Thomsen’s anisotropy parameters, as well as P- and S-wave velocities at seismic and ultrasonic frequencies. The observed effects can be attributed to water adsorption and capillary pressure that are functions of several factors including water saturation. Water adsorption results in a reduction of surface energy and grain-contact stiffness. The capillary pressure affects the effective stress and possibly also the effective pore-fluid modulus, which may be approximated by Brie’s empirical model. Reasonable fits to the low-frequency seismic data are obtained by accounting for these two effects and applying the anisotropic Gassmann model. The strong increase in dispersion with increasing water saturation is attributed to local flow involving adsorbed (bound) water, but a quantitative description is yet to be provided.
24 February 2017 in Geophysical Prospecting
12 August 2016 in Geophysics
Several rocks, and in particular shales, are often described as transversely isotropic (TI) materials. Geophysical data coverage does not always permit reliable determination of all five elastic parameters, neither in seismic and sonic data from the field nor in laboratory measurements. Data may, however, be constrained by the existence of bounds on elastic moduli, derived from the fundamental requirement of positive elastic energy. Conditioned bounds are described for engineering parameters such as Poisson’s ratios as well as anisotropy coefficients such as the moveout parameter and the anellipticity parameter . “Conditioned bounds” means bounds that in general depend on some of the other elastic moduli: The bounds we have evaluated are controlled primarily by P- and S-wave moduli obtained from wave propagation along a symmetry axis and to some extent by P- and S-wave anisotropies. Such data may be acquired more easily from geophysical measurements. We have inspected the laboratory data obtained with various types of shales under different testing conditions, and none of them failed to adapt to the bounds. The data indicate, for instance, clear distinctions between how the proximity to bounds is driven by stress changes for saturated versus nonsaturated shales.
31 May 2019 in Geomechanics and Geophysics for Geo-Energy and Geo-Resources
12 September 2021 in Journal of Geophysical Research: Solid Earth
Shales often show strong elastic anisotropy that originate from the alignment and platy nature of its constituent minerals. Despite its impact on amplitude variation with offset response and seismic time‐shifts, elastic anisotropy of shales is, however, often ignored since it is difficult to measure enough parameters in the field. Being able to correctly estimate anisotropy parameters of shales can therefore significantly improve seismic reservoir characterization. A predictive model is developed by combining existing theories. Properties of locally aligned clay platelets, called domains, are calculated using a rock physics model based on the anisotropic Hashin‐Shtrikman estimates. The effect of domain orientation is then accounted for by the orientation distribution function of domains. The applicability of the model was investigated using existing core measurements. Interesting findings include: (a) most of modeled anisotropy parameters are consistent with the measured values even though only limited information was used for the model parameters optimization, and (b) most of optimized interplatelet medium properties are consistent with the saturated fluid and small interplatelet medium shear modulus suggested by existing studies. These findings imply that the model can be used to predict anisotropy parameters from limited information.