Ján Kováč

Ján Kováč

Auto-generated profile, based on publicly available information

Ján Kováč

Institute of Electrical Engineering, Slovak Academy of Sciences - Institute of Electrical Engineering, Bratislava, SLOVAKIA

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 June 2020 in Superconductor Science and Technology
Verified
Journal Article
Closed access
PDF file
SLShuo Li
Shuo Li
JKJán Kováč
Ján Kováč
EPEnric Pardo
Enric Pardo
In high power density superconducting motors, superconducting tapes are usually stacked and connected together at terminals to improve the current capacity. When a parallel sinusoidal magnetic field is applied on this partially coupled stack, the coupling current is induced and causes additional coupling loss. Usually 3D modeling is needed to calculate the coupling loss but it takes too much computing resource and time. In this paper, a numerical 2D modeling by minimum electromagnetic entropy production (MEMEP) method is developed to speed up the calculation. The presented MEMEP model shows good accuracy and the capability to take the realistic resistance between tapes into account for coupling loss calculation with a high number of mesh element, which agrees to measurements.Thanks to the model, a systemic study of coupling loss on amplitude-dependence, frequency-dependence, resistance-dependence, and length-dependence, is presented and discussed. The results reveal the features of coupling loss which is very helpful devices with multi-tape conductors, such as the stator or rotor windings of motors.

1 February 2019 in Superconductor Science and Technology
Verified
Journal Article
Closed access
PDF file
JŠJán Šouc
Ján Šouc
FGFedor Gömöry
Fedor Gömöry
MSMykola Solovyov
Mykola Solovyov
MVMichal Vojenčiak
Michal Vojenčiak
TKTomáš Kujovič
Tomáš Kujovič
MSMichal Skarba
Michal Skarba
A new cabling machine was constructed for conductor on round core (CORC)-like cable production. Its design allowed us to produce a cable with two layers in one run, each comprising four superconducting tapes. The cable of length of 40 m was made at a production rate of 6 m h −1 by this machine. It consisted of eight Furukawa-SuperPower tapes of width 4 mm and length 50 m wound in two layers on Cu tube with outer diameter 6.35 mm. To detect the influence of the cable winding technology on the superconducting tapes’ properties their critical currents were measured individually on the as-produced cable in the form of a one-layer coil. Afterwards the critical current of the one-layer coil was measured by monitoring the voltages on all tapes while increasing the coil current. The average of these voltages was utilized for coil critical current determination. Then the solenoid with four layers each containing 20 turns was created from the cable and the same measurement procedure was performed to check the influence of cable bending on the solenoid form. The results of these characterizations exclude critical current degradation for any tape of the cable used for solenoid preparation. The measured solenoid critical current of 622.8 A is lower than the simple sum 1240 A of the individual tapes’ critical currents due to the dependence of the tape critical current on the magnetic field. For all measurements the investigated object was immersed into a liquid nitrogen bath. In the case of the solenoid the bath was also cooled down to 66 K.

22 March 2012 in IEEE Transactions on Magnetics
Verified
Journal Article
Closed access
KRK. Richter
K. Richter
RVRastislav Varga
Rastislav Varga
JKJ. Kovac
J. Kovac
Arcady ZhukovArcady Zhukov
Arcady Zhukov
Amorphous glass-coated microwires are magnetic materials well-known by very high domain wall velocities reaching up to 15 km/s. In the previous works was shown, that domain wall dynamics in microwires could be effectively tuned by biasing of additional anisotropies. Here we show the possibility of inducing anisotropy to the microwires. Thermal annealing at 300°C in perpendicular field speeds-up domain wall velocity from 1 km/s (as-cast state) to 6 km/s. On the other side, thermal annealing at the same temperature but without perpendicular field leads to the maximum domain wall velocity of about 4 km/s only. This underlines the importance of two perpendicular anisotropies on fast domain wall velocities in microwires.

22 June 2020 in Superconductor Science and Technology
Verified
Journal Article
Closed access
PDF file
PKPavol Kovac
Pavol Kovac
LKLubomir Kopera
Lubomir Kopera
MHMiroslav Hain
Miroslav Hain
EMELENA MARTÍNEZ
ELENA MARTÍNEZ
JKJán Kováč
Ján Kováč
IHImrich Husek
Imrich Husek
This paper presents the properties of cables made of thin MgB 2 wires with different sheaths manufactured by IMD process. Strong effect of the outer sheath on the J e ( B ) performance was observed and the best properties were obtained for the strongest Cu sheath. It was found that the transversal and longitudinal cables uniformity affects the critical currents in MgB 2 wires made by IMD considerably. We have analyzed the quench dynamics in Rutherford cables with Al + 1.5%A l2 O 3 sheath, when subjected to heat disturbances. Quench triggered in the strands in direct contact with the heater, observing important delays in quench development among strands. Low AC losses were measured for the extra-light Rutherford cable with Ti barrier and Al + 1.5%Al 2 O 3 sheath due to an increased barrier resisitivity and surface Al sheath oxidation, which reduces coupling current loss component effectivelly.

3 March 2023 in Superconductor Science and Technology
Verified
Journal Article
Closed access
PKP Kováč
P Kováč
DBD Berek
D Berek
TMT Melišek
T Melišek
JKJ Kováč
J Kováč
IHI Hušek
I Hušek
JCJ H Choi
J H Choi
Monel-sheathed MgB2 wires with 6, 18 and 54 filaments of diameter 0.83 mm manufactured by Sam Dong Co., Ltd, have been subjected to twisting, drawing and rolling and measurements at low temperatures. R(T), I–V characteristics, critical currents and stress/strain tolerances of these wires were analyzed. Low reduction of critical current (⩽10%) by twisting between 50 mm and 12.5 mm was observed, especially for the wire with 54 filaments, which also showed the best strain tolerance to tension, ∼0.43% at 4.2 K. The engineering current density of the 18-filament wire was decreased by 56% by drawing from 0.83 mm to 0.4 mm, but improved by ∼24% by rolling from 0.83 mm to 0.64 mm. A small uninsulated coil was made from wire flattened from 0.83 mm to 0.64 mm by the wind and react process, resulting in a very high winding packing factor of 0.91 and also a high winding current density of 104 A cm−2 at B ⩽ 5.6 T. The presented properties are interesting for possible applications of these MgB2 wires in DC windings.

5 November 2018 in Superconductor Science and Technology
Verified
Journal Article
Closed access
PDF file
JKJán Kováč
Ján Kováč
MKMiloslav Kulich
Miloslav Kulich
LKLubomir Kopera
Lubomir Kopera
PKPavol Kovac
Pavol Kovac
Magnetization losses of Rutherford MgB 2 cables of different sheath materials (Cu, CuNi and Al + Al 2 O 3 ) made by powder-in-tube and internal magnesium diffusion processes were studied experimentally. Short cable samples consisting of 12 strands were measured in the temperature range from 18 K up to 40 K, external fields up to 70 mT and frequencies 72 Hz and 144 Hz. The effects of inter-strand resistance by soldering and external field orientation (perpendicular and parallel) were also tested. The impact of eddy current losses in the sheath material was determined by the loss measurement in cable samples without MgB 2 . It was found that very high eddy current losses of Cu sheathed strands overlap the hysteresis loss. The lowest AC losses at 20 K were measured for a Rutherford MgB 2 cable with an Al + Al 2 O 3 sheath, which makes it attractive for applications where low loss and also low coil mass are required (e.g. wind turbines or airborne engines).