Berke Gungor

Berke Gungor

Auto-generated profile, based on publicly available information

Berke Gungor

Department of Electrical Engineering, KU Leuven, Leuven, Belgium

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 February 2024 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
KDKristof Dens
Kristof Dens
JVJoren Vaes
Joren Vaes
CBChristian Bluemm
Christian Bluemm
GGGabriel Guimaraes
Gabriel Guimaraes
BGBerke Gungor
Berke Gungor
PRPatrick Reynaert
Patrick Reynaert
This work details the design of a plastic fiber link in 28-nm CMOS, operating in two adjacent bands centered on 117.5 and 152.5 GHz. Each band supports multilevel (PAM-4) intensity-modulated signaling, which can be detected noncoherently, obviating the need for carrier recovery and phase alignment. A rectification-based detector is proposed to support linear noncoherent demodulation. A manifold diplexer is designed on-chip to increase the level of integration. The dual-band link achieves data rates up to 100 Gb/s over a fiber length of 3 m at a power consumption of 574 mW and a bit error rate (BER) better than 2.2e-4, corresponding to the standardized KP4 forward error correction (FEC) threshold. With only the low-band (LB) circuitry active, the link reaches up to 50 Gb/s over a distance of 7 m at a degraded BER of 2.2e-3 and up to 10 Gb/s over 11 m at a BER of 1e-6, representing the highest reported data rates for these link lengths. An energy efficiency reaching as low as 0.8 pJ/bit/m is reported for the 7-m case.

21 January 2020 in IEEE Transactions on Circuits and Systems II: Express Briefs
Verified
Journal Article
Closed access
BUBerktug Ustundag
Berktug Ustundag
ETEsref Turkmen
Esref Turkmen
ABAbdurrahman Burak
Abdurrahman Burak
BGBerke Gungor
Berke Gungor
HKHamza Kandis
Hamza Kandis
YGYasar Gurbuz
Yasar Gurbuz
In this paper, design methodology and measurement results of W-Band Dicke radiometer blocks are presented. The Dicke radiometer blocks are implemented in IHPs 0.13-μm SiGe BiCMOS technology. All the implemented blocks, namely the SPDT switch, LNA and the power detector demonstrate the state of the art performance at W-Band. The SPDT has a measured IL of 1.8 dB and 20 dB isolation. The LNA achieves a peak gain of 22.3 dB and 4.2 dB NF and the PD has a NEP better than 0.5 pW/Hz. To achieve the minimum NETD, all the blocks are designed to be as wideband as possible. Using the measurement and simulation results, the achievable NETD of the radiometer is calculated to be better than 0.5 K.

31 March 2025 in IEEE Transactions on Circuits and Systems I: Regular Papers
Verified
Journal Article
Closed access
BGBerke Gungor
Berke Gungor
PRPatrick Reynaert
Patrick Reynaert
This article presents the design methodology and the measurements of a DC-coupled wideband Active Balun fabricated in a 40-nm CMOS process. An auxiliary balun-based phase and amplitude imbalance compensation method is analyzed and implemented, providing broadband imbalance reduction. Differential T-coil peaking is utilized in each balun for bandwidth extension, and a resistive-feedback inverter is used to interface with $50~\Omega $ at the input. The designed Active Balun achieves 8.2 dB single-ended to differential gain with 28 GHz 3-dB bandwidth, with a peak phase and amplitude imbalance of 4 degrees and 0.3 dB within the bandwidth, respectively. The measured noise figure remains around 5 dB between 5-20 GHz.

3 September 2025 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
BGBerke Gungor
Berke Gungor
PRPatrick Reynaert
Patrick Reynaert
This article presents the design and implementation details of a 280-GHz transmitter (TX) and receiver (RX) pair for J-band communication. Amplitude-shift-keying (ASK) modulation is used to reduce TX and RX complexity, while exploiting the higher available bandwidth (BW) at J-band range (252–325 GHz). The TX and RX are designed for non-coherent operation, removing the requirement of a synchronized local oscillator (LO) signal for demodulation. Both TX and RX, as well as the breakout version of the TX signal chain, are characterized standalone on a probe station. The TX signal chain achieves an average of −3.2-dBm output power at a 263-GHz center with a phase noise of −90 dBc/Hz at 10-MHz offset. The TX achieves an output power of −18 dBm at 270-GHz center, with a 3-dB BW of 45 GHz. The RX demonstrates a conversion gain of 31 dB with a baseband (BB) BW of 0–25 GHz. Modulated measurements are performed for the RX, up to 20-Gbaud NRZ at a 280-GHz carrier, limited by the test setup.

1 October 2018
Verified
Conference Paper
Closed access
BGBerke Gungor
Berke Gungor
ETEsref Turkmen
Esref Turkmen
MYMelik Yazici
Melik Yazici
MKMehmet Kaynak
Mehmet Kaynak
YGYasar Gurbuz
Yasar Gurbuz
This paper presents a W-band LNA implemented in 0.13μm SiGe BiCMOS technology. The designed LNA has a peak gain of 20.5dB at 80GHz with a 3-dB bandwidth greater than 25GHz. The simulated noise figure (NF) is lower than 6.2 dB across the entire W-band with a minimum of 5 dB at 93 GHz. The LNA has input P1dB of -16dBm at 94 GHz. The total quiescent DC power consumption of the designed LNA is 16.6mW with a 1.3V supply voltage. Inductors were utilized in matching networks instead of transmission lines to reduce the chip area. The total integrated circuit occupies an area of 0.33 mm2, and the effective chip area is 0.2mm2, excluding the pads. Simulation results indicate that the designed LNA is suitable to be used in a radiometer that has NETD smaller than 0.5 K.

20 January 2026 in IEEE Solid-State Circuits Magazine
Verified
Journal Article
Closed access
PRPatrick Reynaert
Patrick Reynaert
GVGiacomo Venturini
Giacomo Venturini
BGBerke Gungor
Berke Gungor
SGSenne Gielen
Senne Gielen
On-chip integrated transformers have reshaped high-speed circuit design, offering an extremely compact footprint, seamless co-design with active devices, impedance transformation, galvanic isolation, and a natural suitability for differential operation. Combined with transistor scaling, integrated transformers have enabled access to entirely new frequency ranges even in scaled CMOS nodes, going above 100 GHz. The use of transformers has also enabled ultrawideband designs even at above 100 GHz, with works in the literature pushing above 60% fractional bandwidth (BW). This article covers the basics of transformer-based design, starting from the core concepts and providing detailed overviews of each. Several practical concerns on transformers are also discussed in the later sections. In addition, transformer baluns for single-ended to differential conversion are analyzed, with techniques to improve balance and common-mode (CM) rejection discussed in detail in the later sections.