William Lee Perry

William Lee Perry

Auto-generated profile, based on publicly available information

William Lee Perry

Los Alamos National Laboratory

Research Focus & Metrics

Academic Career Length

32Years (1995-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 April 2004 in Propellants, Explosives, Pyrotechnics
Verified
Journal Article
Closed access
PDF file
WPW. Lee Perry
W. Lee Perry
BSBettina L. Smith
Bettina L. Smith
CBChristopher J. Bulian
Christopher J. Bulian
JBJames R. Busse
James R. Busse
CMClay S. Macomber
Clay S. Macomber
SSSteven F. Son
Steven F. Son

15 October 2010 in Journal of Applied Physics
Verified
Journal Article
Closed access
WPW. Lee Perry
W. Lee Perry
JGJake A. Gunderson
Jake A. Gunderson
MBMatthew M. Balkey
Matthew M. Balkey
PDPeter M. Dickson
Peter M. Dickson
A contaminant (grit) trapped between an explosive and an impacted surface can significantly reduce the impact energy required to initiate a secondary high explosive. Several severe accidents have occurred when an explosive charge was dropped from a height insufficient to cause ignition by heating due only to plastic deformation; the frictional heating from embedded grit has been implicated. Here, we describe an idealization of this situation where a small sample of a polymer-bonded cyclotetramethylenetetranitramine explosive (HMX-PBX 9501), with a 400 μm diameter sphere of silica embedded in the surface, was impacted between instrumented transparent anvils and infrared images were recorded. The instrumentation provided temperature and the work done by the friction between the grit and the anvil surface for the impact process, up to ignition. All experiments were conducted under impact conditions insufficient to cause ignition without grit. Ignition occurred at approximately 500 μs, a grit temperature of 1000 K, and an impact load of 12 kN. A high-fidelity numerical heat transport model, using four-step reversible decomposition kinetics for HMX, clarified the physical mechanism of ignition in the experiment. The model suggested that only a very small part of the silica sphere was heated by the friction process and residual heat in the impacted surface behind the moving grit caused ignition. The model agreed well with the experiment in terms of time and temperature, and we have good confidence in the mechanistic picture provided by the model.

5 December 2013 in Propellants, Explosives, Pyrotechnics
Verified
Journal Article
Closed access
PDF file
ADAmanda L. Higginbotham Duque
Amanda L. Higginbotham Duque
WPWilliam Lee Perry
William Lee Perry
CAChristine M. Anderson‐Cook
Christine M. Anderson‐Cook

1 April 2007 in Journal of Applied Physics
Verified
Journal Article
Closed access
WPW. Lee Perry
W. Lee Perry
JZJonathan Zucker
Jonathan Zucker
PDPeter M. Dickson
Peter M. Dickson
GPGary R. Parker
Gary R. Parker
BABlaine W Asay
Blaine W Asay
Explosives play a significant role in human affairs; however, their behavior in circumstances other than intentional detonation is poorly understood. Accidents may have catastrophic consequences, especially if additional hazardous materials are involved. Abnormal ignition stimuli, such as impact, spark, friction, and heat may lead to a very violent outcome, potentially including detonation. An important factor influencing the behavior subsequent to abnormal ignition is the strength and inertia of the vessel confining the explosive, i.e., the near-field structural/mechanical environment, also known as confinement (inertial or mechanical). However, a comprehensive and quantified understanding of how confinement affects reaction violence does not yet exist. In the research discussed here, we have investigated a wide range of confinement conditions and related the explosive response to the fundamentals of the combustion process in the explosive. In our experiments, a charge of an octahydrotetranitrotetrazine-based plastic bonded explosive (PBX 9501) was loaded into a gun assembly having variable confinement conditions and subjected to a heating profile. The exploding charge breached the confinement and accelerated a projectile down the gun barrel. High bandwidth pressure and volume measurements were made and a first-law analysis was used to obtain enthalpy and power from the raw data. These results were then used to quantify reaction violence. Enthalpy change and power ranged from 0−1.8 kJ and 0−12 MW for 300 mg charges, respectively. Below a confinement strength of 20 MPa, violence was found to decline precipitously with decreasing confinement, while the violence for the heaviest confinement experiments was found to be relatively constant. Both pressure and pressurization rate were found to have critical values to induce and sustain violent reaction.

1 November 2008 in Journal of Applied Physics
Verified
Journal Article
Closed access
PDF file
WPW. Lee Perry
W. Lee Perry
TSThomas D. Sewell
Thomas D. Sewell
BGBrian B. Glover
Brian B. Glover
DDDana M. Dattelbaum
Dana M. Dattelbaum
A model for electromagnetically induced hot spots is developed from the well-established theories of dielectric mixtures, microwave absorption, heat transfer, and thermal ignition. This mathematical model is used to elucidate the interplay among these theories for a microwave heated system of secondary high explosive within which isolated electromagnetically lossy spheres are randomly distributed. Results are shown in this article for the specific case of pentaerythritol tetranitrate with embedded spheres of varying diameter and conductivity illuminated by a uniform time harmonic electromagnetic field of 1, 8, and 15 GHz. It is shown that for a given frequency and electric field strength internal to a particle embedded in a secondary high explosive, there exists a range of values for the particle’s diameter and conductivity for which electromagnetically induced hot-spot ignition of the high explosive is possible. By providing an accurate estimate for the range of necessary geometric and electrical properties of the system, this idealized model can be used to guide potentially complex and otherwise less tractable computational and experimental studies of microwave-induced hot spots. We found that the condition of relatively large particles, with semiconductorlike conductivity, exposed to the highest possible frequency is most favorable for hot-spot ignition.

1 August 2011 in Journal of Applied Physics
Verified
Journal Article
Closed access
PDF file
WPW. Lee Perry
W. Lee Perry
JGJake A. Gunderson
Jake A. Gunderson
BGBrian B. Glover
Brian B. Glover
DDDana M. Dattelbaum
Dana M. Dattelbaum
In order to more fully understand the factors that influence the thermal “hot-spot” initiation of high explosives, we have chosen a model system for study that uses the internal and localized dissipation of long wavelength electromagnetic energy (microwaves). High purity organic crystals generally interact weakly with microwave energy. Therefore, the addition of electromagnetically absorbing inclusions of silicon carbide provides a tractable system for the study of hot-spot ignition phenomena. Previously, we developed a simple analytic model that illuminates the important physical factors. In this work, we verify the relationships of the analytic model using a series of experiments and a numerical model.