13 November 2018 in Progress in Earth and Planetary Science
The dusty regolith covering the surfaces of asteroids and planetary satellites differs in size, shape, and composition from terrestrial soil particles and is subject to environmental conditions very different from those found on Earth. This regolith evolves in a low ambient pressure and low-gravity environment. Its response to low-velocity impacts, such as those that may accompany human and robotic exploration activities, may be completely different than what is encountered on Earth. Experimental studies of the response of planetary regolith in the relevant environmental conditions are thus necessary to facilitate future Solar System exploration activities.We combined the results and provided new data analysis elements for a series of impact experiments into simulated planetary regolith in low-gravity conditions using two experimental setups and a range of microgravity platforms. The Physics of Regolith Impacts in Microgravity Experiment (PRIME) flew on several parabolic aircraft flights, enabling the recording of impacts into granular materials at speeds of ∼ 4–230 cm/s. The COLLisions Into Dust Experiment (COLLIDE) is conceptually close to the PRIME setup. It flew on the Space Shuttle in 1998 and 2001 and more recently on the Blue Origin New Shepard rocket, recording impacts into simulated regolith at speeds between 1 and 120 cm/s.Results of these experimental campaigns found that there is a significant change in the regolith behavior with the gravity environment. In a 10 −2g environment (with g being the gravity acceleration at the surface of the Earth), only embedding of the impactor was observed and ejecta production was produced for most impacts at > 20 cm/s. Once at microgravity levels ( 10 cm/s. The measured ejecta speeds were somewhat lower than the ones measured at reduced-gravity levels, but the ejected masses were higher. In general, the mean ejecta velocity shows a power-law dependence on the impact energy with an index of ∼ 0.5. When projectile rebound occurred, we observed that its coefficients of restitution on the bed of regolith simulant decrease by a factor of 10 with increasing impact speeds from ∼ 5 up to 100 cm/s. We could also observe an increased cohesion between the JSC-1 grains compared to the quartz sand targets.
19 June 2024 in Advances In Space Research
16 October 2019 in Astronomy & Astrophysics
Context. The current model of planet formation lacks a good understanding of the growth of dust particles inside the protoplanetary disk beyond mm sizes. A similar collisional regime exists in dense planetary rings. In order to investigate the low-velocity collisions between this type of particles, the NanoRocks experiment was flown on the International Space Station (ISS) between September 2014 and March 2016. We present the results of this experiment. Aims. The objectives of our data analysis are the quantification of the damping of energy in systems of multiple particles in the 0.1–1 mm size range while they are in the bouncing regime, and the study of the formation of clusters through sticking collisions between particles. Methods. We developed statistical methods for the analysis of the large quantity of collision data collected by the experiment. We measured the average motion of particles, the moment of clustering, and the cluster size formed. In addition, we ran simple numerical simulations in order to validate our measurements. Results. We computed the average coefficient of restitution (COR) of collisions and find values ranging from 0.55 for systems including a population of fine grains to 0.94 for systems of denser particles. We also measured the sticking threshold velocities and find values around 1 cm s−1, consistent with the current dust collision models based on independently collected experimental data. Conclusions. Our findings have the following implications that can be useful for the simulation of particles in PPDs and planetary rings: (1) The average COR of collisions between same-sized free-floating particles at low speeds (<2 cm s−1) is not dependent on the collision velocity; (2) The simplified approach of using a constant COR value will accurately reproduce the average behavior of a particle system during collisional cooling; (3) At speeds below 5 mm s−1, the influence of particle rotation becomes apparent on the collision behavior; (4) Current dust collision models predicting sticking thresholds are robust.
1 June 2025 in Review of Scientific Instruments
This paper presents the design and development of a Shear and Compression Cell (SCC) for measuring the mechanical properties of granular materials in low-gravity environments. This research is motivated by the increasing interest in planetary exploration missions that involve surface interactions, such as those to asteroids and moons. The SCC is designed to measure key mechanical properties, including Young’s modulus, angle of internal friction, bulk cohesion, and tensile strength, under both reduced gravity and microgravity conditions. Using a drop tower with interchangeable configurations, we can simulate the gravitational environments of celestial bodies such as the Moon and Titan. The SCC, coupled with the drop tower, provides a valuable tool for understanding the behavior of regolith materials and their implications for future space exploration missions.
1 July 2022 in The Planetary Science Journal
We present the results of a series of laboratory low-speed impacts (< 4 m s−1) of centimeter-sized spherical projectiles into simulated dry and icy regolith samples. The target material was comprised of JSC-1 (Johnson Space Center) lunar simulant grains in the size range 100–250 μm, mixed with similar-sized water ice grains. Impacts were performed under vacuum, either at room temperature for JSC-1 samples or at cryogenic temperatures (<150 K) for icy mixtures. We measured the ejecta masses from a collection plate and impact crater dimensions from post-impact crater photographs. We find that both the ejecta masses and crater diameters followed trends predicted by established scaling laws, albeit with different fitting parameters, and we were able to fit a strength regime π scaling to our measured crater diameters. The water ice in our target material took two forms: grains mixed with the regolith grains and frost from air condensation coating regolith grains. In both cases, the presence of water ice in the sample led to lower ejected masses and smaller crater sizes. In addition, our measured crater sizes were several orders of magnitude larger than expected for impacts into solid rock or water ice. Using our measured scaling parameters, we applied our findings to a planetary context for the study of secondary craters on icy moons, as well as eroding collisions occurring in Saturn’s rings. We found that the deviation of our measurements from solid targets and from commonly used scaling parameters allowed us to reconcile our measurements with the models in both cases.