1 March 2014 in Chemical Geology
International audienceModelling the progress of geochemical processes in CO₂storage sites is frustrated by uncertainties in the rates of CO₂ flow and dissolution, and in the rates and controlling mechanisms of fluid-mineral reactions that stabilise the CO₂ in geological reservoirs. Dissolution of CO₂ must be controlled by the complexities of 2-phase flow of CO₂ and formation brines and the smaller-scale heterogeneities in the permeability in the reservoirs which increase the fluid contact areas. The subsequent fluid mineral reactions may increase storage security by precipitating CO₂ in carbonate minerals but the consequences of fluid-mineral reactions on caprock rocks or potential leakage pathways up fault zones are less certain as the CO₂-charged brines may either corrode minerals or decrease permeabilities by precipitating carbonates. Observations from CO₂-injection experiments and natural analogues provide important constraints on the rates of CO₂ and brine flow and on the progress of CO₂ dissolution and mineral-fluid reactions. In these experiments brines in contact with the propagating plume appear to rapidly saturate with CO₂. Dissolution of the CO₂ drives the dissolution of oxide and carbonate minerals, on times scales of days to weeks. These reactions buffer fluid pH and produce alkalinity such that carbonate dissolution moves to carbonate precipitation over time-scales of weeks to months. The dissolution of Fe-oxide grain coatings and the release of Fe to solution is important in stabilising insoluble Fe-Mg-Ca carbonate minerals but the rate limiting step for carbonate mineral precipitation is the transport of CO₂-charged brines and silicate mineral dissolution rates. Observations from CO₂-EOR experiments and natural analogues suggest that the silicate mineral dissolution reactions are initially fast in the low pH fluids surrounding the CO₂ plume but that reaction progress over months to years drives minerals towards thermodynamic equilibrium and dissolution rates slow over 2-5 orders of magnitude as equilibrium is approached. The sluggish dissolution of silicate minerals is likely to preside over the long-term fate of the CO₂ in geological reservoirs. Observations from injection experiments and natural analogues suggest that the potentially harmful trace elements mobilised by the drop in pH are immobilised as adsorbed and precipitated phases as fluid pH is buffered across mineral reaction fronts. There are very few observations of caprock exposed to CO₂-rich brines. Preliminary examination of core recently recovered from scientific drilling of a natural CO₂ accumulation in Utah suggests that the diffusion of CO₂ into reservoir caprocks drives dissolution of Fe-oxides but subsequent precipitation of carbonate minerals likely retards the diffusion distance of the CO₂. At this site thin siltstone layers are shown to be effective seals to the CO₂-charged fluids, which has significant implications for the long term security of CO₂ in geological reservoirs
1 July 2009 in Earth and Planetary Science Letters
22 April 2012 in Nature Geoscience
1 January 2017 in Geological Society, London, Special Publications
Porosity of shales is an important parameter that impacts rock strength for seal or wellbore integrity, gas-in-place calculations for unconventional resources or the diffusional solute and gas transport in these microporous materials. From a well section obtained from the Mont Terri Underground Rock Laboratory in St Ursanne, Switzerland, we determined porosity, pore size distribution and specific surface areas on a set of 13 Opalinus Clay samples. The porosity methods employed are helium-pycnometry, water and mercury injection porosimetry, liquid saturation and immersion, and low pressure N 2 sorption, as well as small-angle to ultra-small-angle neutron scattering (SANS–USANS). These were used in addition to mineralogical and geochemical methods for sample analysis that comprise X-ray diffraction, X-ray fluorescence, total organic carbon content and cation exchange capacity. We find large variations in total porosity, ranging from approximately 23% for the neutron-scattering method to approximately 10% for mercury injection porosimetry. These differences can partly be related to differences in pore accessibility, while no or negligible inaccessible porosity was found. Pore volume distributions between neutron scattering and low-pressure sorption compare very well but differ significantly from those obtained from mercury porosimetry: this is realistic since the latter provides information on pore throats only, and the two former methods on pore throats and pore bodies. Finally, we find that specific surface areas determined using low-pressure sorption and neutron scattering match well.
26 April 2021 in Water Resources Research
Heterogeneous fracture aperture distribution, dictated by surface roughness, mechanical rock and fracture properties, and effective stress, limits the predictive capabilities of many reservoir‐scale models that commonly assume smooth fracture walls. Numerous experimental studies have probed key hydromechanical responses in single fractures; however, many are constrained by difficulties associated with sample preparation and quantitative roughness characterization. Here, we systematically examine the effect of roughness on fluid flow properties by 3D printing seven self‐affine fractures, each with controlled roughness distributions akin to those observed in nature. Photogrammetric microscopy was employed to validate the 3D topology of each printed fracture surface, enabling quantification using traditional roughness metrics, namely the Joint Roughness Coefficient (JRC). Core‐flooding experiments performed on each fracture across eight incremental confining pressure increases (11–25 bar), shows smoother fractures (JRC < 5.5) exhibit minor permeability variation, whilst rougher fractures (JRC > 7) show as much as a 219% permeability increase. Micro‐computed tomography imaging of the roughest fracture under varying effective stresses (5–13.8 bar), coupled with inspection into the degree of similarity between fracture closure behavior in 3D‐printed and natural rock fractures, highlight the capabilities of 3D‐printed materials to act as useful analogs to natural rocks. Comparison of experimental data to existing empirical aperture‐permeability models demonstrates that fracture contact area is a better permeability predictor than roughness when the mechanical aperture is below ∼20 μm. Such findings are relevant for models incorporating the effects of heterogeneous aperture structures and applied stress to predict fracture flow in the deep subsurface.