Thomas Vogt

Thomas Vogt

Auto-generated profile, based on publicly available information

Thomas Vogt

Department of Mechanical Engineering, Imperial College, London SW7 2BX, United Kingdom

Research Focus & Metrics

Academic Career Length

26Years (2001-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2018 in NDT & E International
Verified
Journal Article
Open access
SHS. Heinlein
S. Heinlein
PCP. Cawley
P. Cawley
TVT.K. Vogt
T.K. Vogt
This paper investigates the reflection of the torsional T(0,1) mode from defects in pipe bends. The effect of varying circumferential and angular position along the pipe bend, as well as the influence of the bend radius, is investigated via 3D finite element simulations. The results show that the reflection expected from a small defect varies significantly with position, the minimum reflection coefficient being about 10% of that from a comparable defect in a straight pipe, while maxima of around four times the straight pipe value are seen. The areas of low detectability are mainly found on the bend intrados and those of high detectability close to its extrados; similar effects are seen in bends with radii varying from one to twenty pipe diameters. It is shown that the reflection from a defect at a given location is roughly proportional to the square of the von Mises stress produced by the transmitted wave at that position. This holds for defects such as circumferential cracks, the detailed subject of this investigation, and is also expected to be valid for corrosion patches; it will not hold for axial cracks. The results explain the low reflection seen from a simulated corrosion defect at a bend in a previous investigation

1 July 2009 in Insight - Non-Destructive Testing and Condition Monitoring
Verified
Journal Article
Closed access
DAD N Alleyne
D N Alleyne
TVT Vogt
T Vogt
PCP Cawley
P Cawley

28 February 2003 in The Journal of the Acoustical Society of America
Verified
Journal Article
Closed access
PDF file
TVT. Vogt
T. Vogt
MLM. Lowe
M. Lowe
PCP. Cawley
P. Cawley
The scattering of ultrasonic guided waves at a point where a free cylindrical waveguide enters an embedding material is investigated. A modal solution that is valid when the guided waves are incident from the free section of the waveguide is developed. It is shown that in this case it is valid to consider only the modal fields over the cross section of the waveguide, neglecting the fields in the embedding material. As an application, the scattering of the lowest-order longitudinal mode in a cylindrical waveguide, L(0,1), is examined in detail. As well as considering epoxy resin as an embedding material, the case where the embedding material is replaced by a perfectly rigid boundary is discussed. The latter gives some insight into the role of nonpropagating and inhomogeneous waveguide modes in the scattering process. The results from the modal solution are validated using Finite Element modeling, very good agreement being obtained.

27 August 2003 in The Journal of the Acoustical Society of America
Verified
Journal Article
Closed access
PDF file
TVT. Vogt
T. Vogt
MLM. Lowe
M. Lowe
PCP. Cawley
P. Cawley
The possibility of using ultrasonic guided waves for monitoring the cure process of epoxy resins is investigated. The two techniques presented use a wire waveguide which is partly embedded in the resin. The first technique is based on the measurement of attenuation due to leakage of bulk waves into the resin surrounding the waveguide. The second technique measures the reflection of the guided wave that occurs at the point where the waveguide enters the resin. Both the attenuation and the reflection coefficient change significantly during cure, and the numerical methods to relate these to the material properties of the curing resin are presented in this paper. The results from the modeling are experimentally verified and show good agreement. The applicability of each testing method is discussed, and typical cure-monitoring curves are presented.

12 September 2018 in Structural Health Monitoring
Verified
Journal Article
Open access
SHSebastian Heinlein
Sebastian Heinlein
PCPeter Cawley
Peter Cawley
TVThomas Vogt
Thomas Vogt
Validation of the performance of guided wave structural health monitoring systems is vital if they are to be widely deployed; testing the damage detection ability of a system by introducing different types of damage at varying locations is very costly and cannot be performed on a system in operation. Estimating the damage detection ability of a system solely by numerical simulations is not possible as complex environmental effects cannot be accounted for. In this study, a methodology was tested and verified that uses finite element simulations to superimpose defect signals onto measurements collected from a defect-free structure. These signals are acquired from the structure of interest under varying environmental and operational conditions for an initial monitoring period. Measurements collected in a previous blind trial of an L-shaped pipe section, onto which a number of corrosion-like defects were introduced, were utilised during this investigation. The growth of three of these defects was replicated using finite element analysis and the simulated reflections were superimposed onto signals collected on the defect-free test pipe. The signal changes and limits of reliable detection predicted from the synthetic defect reflections superimposed on the measurements from the undamaged complex structure agreed well with the changes due to real damage measured on the same structure. This methodology is of great value for any structural health monitoring system as it allows for the minimum detectable defect size to be estimated for specific geometries and damage locations in a quick and efficient manner without the need for multiple test structures while accounting for environmental variations.

1 January 2004 in Geophysics
Verified
Journal Article
Closed access
RLRob Long
Rob Long
TVThomas Vogt
Thomas Vogt
MLMike Lowe
Mike Lowe
PCPeter Cawley
Peter Cawley
A technique is presented that uses a circular ultrasonic waveguide to measure the bulk shear (S-wave) and longitudinal (P-wave) velocities of unconsolidated media, with particular application to near-surface soils. The technique requires measuring the attenuation characteristics of the fundamental longitudinal mode that propagates along an embedded bar, from which the acoustic properties of the surrounding medium are inferred. The principles behind the technique are discussed, and the results of an experimental laboratory validation are presented, followed by details of in-situ soil property measurements obtained at various sites in urban areas of the United Kingdom.