2 June 2021 in Physical Review B
We have studied the epitaxial (111) films grown on (0001) substrates of different thickness at various temperature and discovered colossal intrinsic exchange bias up to 7 ± 2 kOe. X-ray and electron diffraction clearly indicate an interfacial layer about 2 nm of different crystal structure from the “bulk” part of the film. The thickness dependence of the exchange bias suggests a hidden antiferromagnetic composition in the interfacial layer that couples to the ferrimagnetic “bulk” part of the film as the origin of the exchange bias. Considering the structural, magnetic, and electronic structure, CoO has been identified as the most likely candidate of the antiferromagnetic composition in the interfacial layer. This work suggests a path for enhancing intrinsic exchange bias using combination of film and substrate of large structural differences, highlighting the role of interfacial atomic and electronic reconstructions.
10 January 2022 in Journal of Vacuum Science & Technology A
In spite of the absence of significant segregation of either cobalt oxide or iron oxide, core level photoemission binding energy shifts tend to indicate that the surface is significantly different from the bulk for CoFe2O4(111) thin films grown on Al2O3(0001). CoFe2O4(111) thin films show a surface-to-bulk core level shift in both the Co 2p and Fe 2p core level photoemission spectra. Surface weighted components in the core level photoemission spectra of both Co 2p3/2 and Fe 2p3/2 can be distinguished from the bulk components, by angle-resolved x-ray photoemission spectroscopy, for CoFe2O4(111) thin films. The surface termination of CoFe2O4(111) contains both Co and Fe with no evidence of strong preferential surface termination of either an iron or cobalt oxide, except for CoFe2O4(111) in the thin film limit. With extensive annealing above room temperature, the cobalt oxide component of very thin CoFe2O4(111) films, grown on Al2O3 (0001), will lose oxygen.
9 January 2026 in Journal of Physics: Condensed Matter
Improper ferroelectricity in hexagonal rare-earth manganites (h-RMnO3, R = Ho-Lu, Y, Sc) arises from a geometric distortion as the primary order parameter, resilient to depolarizing fields and promising for ultrathin ferroelectric devices. However, the substrate-induced interface clamping effect, which suppresses the geometric distortion in the sub-nanometer regime, has thus far hindered the realization of two-dimensional improper ferroelectrics. This study demonstrates that doping with calcium can enhance ferroelectric structural distortion in h-LuMnO3 thin films. Compressively strained h-Lu₁₋ₓCaₓMnO3 (x = 0.1, 0.2, 0.3, 0.4, 0.5) epitaxial thin films were stabilized on sapphire substrates using an h-ScFeO3 buffer layer. We have found that the interface clamping effect is entirely overcome when the doping concentration reaches x ≥ 0.2, establishing a potential quasi-2D ferroelectric system with a remarkably high estimated structural transition temperature of larger than 1200 K inferred indirectly from temperature-resolved RHEED. This finding suggests a general strain engineering strategy to enhance improper ferroelectricity in hexagonal manganites.
18 September 2024 in Journal of Physics: Condensed Matter
Intrinsic exchange bias is known as the unidirectional exchange anisotropy that emerges in a nominally single-component ferro-(ferri-)magnetic system. In this work, with magnetic and structural characterizations, we demonstrate that intrinsic exchange bias is a general phenomenon in (Ni, Co, Fe)-based spinel oxide films deposited on -Al2O3(0001) substrates, due to the emergence of a rock-salt interfacial layer consisting of antiferromagnetic CoO from interfacial reconstruction. We show that in NixCoyFe3−x−yO4(111)/ -Al2O3(0001) films, intrinsic exchange bias and interfacial reconstruction have consistent dependences on Co concentrationy, while the Ni and Fe concentration appears to be less important. This work establishes a family of intrinsic exchange bias materials with great tunability by stoichiometry and highlights the strategy of interface engineering in controlling material functionalities.