14 July 2015 in Advances in Materials Science and Engineering
Steel structures coated with fiber-reinforced polymer (FRP) composites have gained wide acceptance in marine industry due to their high strength-to-weight ratio, good protection from environmental degradation, and impact loads. In this study, adhesive bonding performance of single-lap bonded joints composed of steel coated with FRP has been investigated experimentally for three different surface roughness and two epoxy types. Single-lap bonded joints have been tested under tensile loading. The adhesive bonding performance has been evaluated by calculating the strain energy values. The results reveal that the surface roughness of steel has a significant effect on the bonding performance of steel to FRP combinations and the performance of the resin can be improved by using the primer in an economical way.
26 July 2016 in Advances in Materials Science and Engineering
This paper deals with the friction welding of the tube yoke and the tube of the drive shaft used in light commercial vehicles. Tube yoke made from hot forged microalloyed steel and the tube made from cold drawn steel, with a ratio (thickness/outside diameter ratio) of less than 0.1, were successfully welded by friction welding method. Hardness distributions on both sides of the welded joint across the welding interface were determined and the microstructure of the joint was investigated. Furthermore, joint strength was tested under tensile, static torsional, and torsional fatigue loadings. The tested data were analyzed by Weibull distribution. The maximum hardness value along the welded joint was detected as 553 Hv1. The lowest detected tensile strength of the joint was 13% less than the base materials’ tensile strength. The torsional load carrying capacity of the friction welded thin walled tubular joint without any damage was obtained as 4.252,5 Nm in 95% confidence interval. After conducting fully reversed torsional fatigue tests, the fatigue life of friction welded tubular joints was detected as 220.066,3 cycles.
31 August 2005 in Composite Structures
1 January 2026 in Express Polymer Letters
20 March 2020 in Mühendislik Bilimleri ve Tasarım Dergisi
Tr en Polimer esaslı termoplastik malzeme grubunda yer alan poliamid, yüksek mukavemet ve yüksek sıcaklıklara dayanma özelliklerinden dolayı endüstrinin farklı alanlarında yaygın olarak kullanılmaktadır. Poliamid (PA) malzemelerin monomer yapısına bağlı olarak nem alma davranışları malzemenin mekanik özelliklerini önemli ölçüde etkilemektedir. Endüstrinin farklı alanlarında yarı mamul olarak üretilen ürünlerin, üretim şekli ve kullanım alanlarına bağlı olarak kaynak yöntemi ile birleştirilmesi gerekmektedir. Bu çalışmada, PA6 ve cam elyaf katkılı türevlerinden üretilmiş olan numuneler sıcak plaka kaynak yöntemi ile birleştirilmiştir. Nem alma davranışının kaynak mukavemetine etkisini araştırmak amacıyla, numuneler -20 oC ile 60 oC sıcaklık aralığında 16 saat bekletilerek yapay olarak şartlandırılmıştır. Kaynaklı numunelerde, şartlandırma sıcaklıklarının artması ile PA6 malzemede nem alma oranının arttığı, mekanik mukavemet değerlerinin azaldığı ve yüzde uzama değerlerinin ise artığı gözlenmiştir. Cam elyaf katkılı numunelerde ise nem alma oranında önemli bir değişiklik olmamıştır. Şartlandırma sonrasında, en yüksek kaynak mukavemeti PA6 malzemede 0 oC’ de 34 MPa, PA6 GF15’te -10 oC’de 38MPa ve PA6 GF30’da ise -20 oC’de 41MPa olarak ölçülmüştür. Polyamide, which belongs to the group of polymer-based thermoplastic materials, is widely used in different fields of industry due to its high strength and high temperature resistance properties. Depending on the monomer structure of polyamide (PA) materials, the dehumidification behavior significantly affects the mechanical properties of polyamide-based materials. Semi-finished products manufactured for different areas of the industry should be joined by means of welding methods depending on the production methods and usage areas. In this study, samples produced from PA6 and glass fiber reinforced PA6 were combined by hot plate welding method. In order to investigate the effect of dehumidification behavior on the welding strength, the samples were artificially conditioned at a temperature range of -20 oC to 60 oC for 16 hours. In welded samples, it was observed that the dehumidification rate of PA6 material increased, mechanical strength values decreased and percent elongation values increased with the increase of conditioning temperatures. There was no significant change in the rate of dehumidification for glass-fiber reinforced samples. After conditioning, the highest weld strength was measured as 34 MPa at 0 oC for PA6, 38MPa at -10 oC for PA6 GF15 and 41MPa at -20 oC for PA6 GF30.