13 May 2019 in Journal of Circuits, Systems and Computers
1 October 2018 in Microprocessors and Microsystems
19 June 2018 in International Journal of Circuit Theory and Applications
29 August 2024 in International Journal of Information Security
The Internet of Things (IoT) nodes consist of sensors that collect environmental data and then perform data exchange with surrounding nodes and gateways. Cybersecurity attacks pose a threat to the data security that is being transmitted in any IoT network. Cryptographic primitives are widely adopted to address these threats; however, the substantial computation demands limit their applicability in the IoT ecosystem. In addition, each IoT node varies with respect to the area and throughput (TP) requirements, thus demanding flexible implementation for encryption/decryption processes. To solve these issues, this work implements the NIST lightweight cryptography standard, Ascon, on a SAED 32 nm process design kit (PDK) library by employing loop folded, loop unrolled and fully unrolled architectures. The fully unrolled architecture can achieve the highest TP but at the cost of higher area utilisation. Unrolling by a lower factor results in lower area implementations, enabling the exploration of design space to tackle the trade-off between area and TP performance of the design. The implementation results show that, for loop folded architecture, Ascon-128 and Ascon-128a require 36.7k $$\upmu \textrm{m}^{2}$$ and 38.5k $$\upmu \textrm{m}^{2}$$ chip area, respectively compared to 277.1k $$\upmu \textrm{m}^{2}$$ and 306.6k $$\upmu \textrm{m}^{2}$$ required by their fully unrolled implementations. The proposed implementation strategies can adjust the number of rounds to accommodate the varied requirements of IoT ecosystems. An implementation with an open-source 45 nm PDK library is also undertaken for enhanced generalization and reproducibility of the results.
6 June 2024 in IEEE Embedded Systems Letters
Unifying the forward and inverse operations of the number theoretic transform (NTT) into a single hardware module is a common practice when designing polynomial coefficient multiplier accelerators as used in the post-quantum cryptographic algorithms. This work experimentally evaluates that this design unification is not always advantageous. In this context, we present three NTT hardware architectures: (i) A forward NTT (FNTT) architecture, (ii) An inverse NTT (INTT) architecture and (iii) A unified NTT (UNTT) architecture for computing the FNTT and INTT computations on a single design. We benchmark our throughput/area and energy/area evaluations on Xilinx Virtex-7 FPGA and 28nm ASIC platforms. The standalone FNTT and INTT designs, on average on FPGA, exhibit 4.66× and 3.75× higher throughput/area and energy/area values respectively than the UNTT design. Similarly, the individual FNTT and INTT designs, on average on ASIC, achieve 1.25× and 1.09× higher throughput/area and energy/area values respectively, compared to the UNTT design.
3 April 2020 in IET Computers & Digital Techniques
Recent studies have shown that existing elliptic curve‐based cryptographic standards provide backdoors for manipulation and hence compromise the security. In this regard, two new elliptic curves known as Curve448 and Curve25519 are recently recommended by IETF for transport layer security future generations. Hence, cryptosystems built over these elliptic curves are expected to play a vital role in the near future for secure communications. A high‐speed elliptic curve cryptographic processor (ECCP) for the Curve448 is proposed in this study. The area of the ECCP is optimised by performing different modular operations required for the elliptic curve Diffie–Hellman protocol through a unified architecture. The critical path delay of the proposed ECCP is optimised by adopting the redundant‐signed‐digit technique for arithmetic operations. The segmentation approach is introduced to reduce the required number of clock cycles for the ECCP. The proposed ECCP is developed using look‐up‐tables (LUTs) only, and hence it can be ported to any field‐programmable gate array family or standard ASIC libraries. The authors' ECCP design offers higher speed without any significant area overhead to recent designs reported in the literature.