1 March 2017 in Russian Journal of Non-Ferrous Metals
The results of experimental investigations into the zeta potential of ultrafine sulfides (chalcopyrite, tennantite, galenite, sphalerite, pyrite, and pyrrhotine), the floatability of monomineral fractions of sulfides of the floatation coarseness (–0.1 + 0.05 mm) in a mechanical flotation machine, and the floatability fine particles of sulfide (–0.044 + 0.010 mm) in the Hallimond tube are presented. The preparation procedure of ultrafine powders and sulfhydril collectors to measure the zeta potential is presented. Zeta potentials of the surface of mineral particles and insoluble forms of sulfhydril collectors are investigated in the pH range from 2.0 to 12.5 (an acidic medium was formed by using H2SO4 and basic one by using NaOH or Ca(OH)2), and various values of zeta potentials are found for sulfides in the sodium hydroxide and lime medium. Zeta potentials for all sulfides are negative in the NaOH medium at pH > 9.5, they are positive (1–18 mV) in the Ca(OH)2 medium at pH > 11, and zeta potentials for chalcopyrite are positive in the studied range \(p{H_{Ca{{\left( {OH} \right)}_2}}}\) 9.0–12.5. The values of the isoelectric point in the medium of sulfuric acid and sodium hydroxide are as follows: for chalcopyrite—pH 6.5 and 8.8, for tennantite—pH 3.0, for sphalerite—pH 5.1 and 6.4, for pyrite—pH 3.1 and 8.9, and for pyrrhotine—pH 7.0. In the lime medium, the value for tennantite and sphalerite pH 12.0, for galenite—pH 11.2, for pyrite—pH 9.5 and 11.2, and for pyrrhotine—pH 9.5 and 12.1. Measurements of zeta potentials of ultrafine sulfide particles give the opportunity to refine the interaction mechanism of sulfhydril collectors with sulfides and associate the nonselective recovery of final tailings of sulfides in the highly alkaline lime medium with the contribution of the electrostatic component during the adhesion of ultrafine sulfide particles on bubbles and their mechanical carryout into the froth product.
29 March 2018 in Russian Journal of Non-Ferrous Metals
The results of material composition studies of four samples of refractory copper-bearing ores of the Uzelga deposit are presented along with the results of studies of technological solutions to...
1 March 2016 in Journal of Mining Science
1 September 2018 in Journal of Mining Science
The influence of structural characteristics and interaction parameters of minerals on separation method of lead-bearing complex ore in Russia is analyzed. Based on the studies of deep dissociation of...
30 June 2016 in Tsvetnye Metally
Results of investigation of flotation properties of separated minerals were analyzed together with the small size distribution of metals and minerals in the samples of ingrained and massive pyritic ores and flotation products, obtained in laboratory and industrial conditions. Increasing of a ton of raw grinding improves the ore mineral release. The first stage includes the release of macrocrystalline modifications and easily-sliming corroded and fragile types of ore mineral associations of pyrite, secondary copper sulfides, tennantite and rock minerals. Release of growths in ingrained and massive pyritic ores requires various grinding time. The quantity of growths in fine and coarse grades in flotation tails correlates with their distribution in ore material, which shows the discrepancy of process flowsheets to the physical and chemical properties of ore minerals. The ways of improvement of schemes and modes of grinding and flotation were defined: including the varieties of copper minerals and sphalerite into the scheme of inter-cycle operations of continuous ore flotation; release of pyrite modifications in tail fractions in main and final operations.This work was carried out with the financial support of the grants of the Russian Scientific Fund (project No. 214170039).
1 July 2016 in Journal of Mining Science
Monomineral and compound fractions, ore material and concentrates are used to study the effect of basic processing factors on mineral separation. The key criteria are determined to choose a method of selective extraction of minerals and their species in various cycles of a process flow chart. Such key criteria include: degree of activating effect of copper minerals on other sulfides; multifunction role of iron compounds; medium pH values; combination and concentration of depressing ions of modifying reagents; ratios of selective collectors in their combinations; scientific principles of flow chart designing; principles of concentration and recovery of minerals in different processes of dressing.