Dominik Kaserer

Dominik Kaserer

Auto-generated profile, based on publicly available information

Dominik Kaserer

Institute of Robotics, Johannes Kepler University Linz, Linz, Austria

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 November 2018 in IEEE Transactions on Robotics
Verified
Journal Article
Closed access
DKDominik Kaserer
Dominik Kaserer
HGHubert Gattringer
Hubert Gattringer
AMAndreas Mueller
Andreas Mueller
This paper presents a new dynamic programming (DP) approach to the optimal path following problem. The method rests on an interpolation in the phase plane so that the resulting joint accelerations and joint torques are continuous. This allows for taking into account limits on the joint jerks and torque rates in addition to joint velocities, accelerations, torques, and the mechanical power. Most methods proposed in the literature yield values of optimal trajectories at discrete sampling times so that this must be interpolated subsequently to the trajectory optimization. This causes violations of the joint jerk and torque rate limits. The proposed method does not suffer from this problem, which is a main feature of this approach. Unlike most of the previously proposed methods, joint jerk and torque rate limits are addressed with a reasonable increase in the computation time of DP algorithms. Special attention is given to experimental validation of the optimization results. The presented experimental results confirm the importance of taking the motor torque characteristics as well as the Coulomb and viscous friction into account. Neglecting these effects (as most previous publications did) leads to trajectories that cannot be performed by real manipulators. Apart from DP, other approaches with smaller computation times exist. However, most of these methods are either limited to the time optimal case (which might not always be the desired criterion) and are not able to handle all earlier mentioned constraints or cannot take into account viscous friction effects. Apart from that a sequential convex programming (SCP) approach exists, which accounts for the same constraints as the presented approach. Therefore, the proposed DP approach is compared to this SCP method and an example is presented where the time optimal trajectory is performed by a real manipulator.

10 March 2022 in Mechatronics
Verified
Journal Article
Closed access
HGHubert Gattringer
Hubert Gattringer
AMAndreas Mueller
Andreas Mueller
MOMatthias Oberherber
Matthias Oberherber
DKDominik Kaserer
Dominik Kaserer

30 January 2020 in IEEE Robotics and Automation Letters
Verified
Journal Article
Closed access
DKDominik Kaserer
Dominik Kaserer
HGHubert Gattringer
Hubert Gattringer
AMAndreas Mueller
Andreas Mueller
Cooperative grasping refers to the situation when an object is manipulated by multiple robots and the grasp is achieved by the unilateral contact between the robots and the object. This is different from the cooperation of multiple robots where each robot rigidly grasps the object. Motion planning of cooperative grasping tasks involves active force control of the interaction wrench in order to ensure stable grasp. This becomes particularly challenging when aiming at time optimal motions. It is crucial that the trajectories are continuous up to third-order, in order to satisfy velocity, acceleration, and jerk as well as torque limits of the robots. A solution approach is presented for the time optimal path following of two robots performing cooperative grasping tasks. The time optimal path is determined with a dynamic programming method. An admittance control scheme in task space is proposed and used to generate the contact wrench. The method is applicable to

1 October 2016
Verified
Conference Paper
Closed access
DKDominik Kaserer
Dominik Kaserer
HGHubert Gattringer
Hubert Gattringer
AMAndreas Müller
Andreas Müller
Nowadays robotic manipulators are used as multi-purpose tools and must be able to complete various tasks. Pure position control schemes are often not sufficient to fulfill the requirements of these tasks. Interaction with the environment requires an extension of the conventional position control in order to achieve a desired compliance, and thus to limit the impact in order to avoid damaging of involved objects. This paper presents an admittance control scheme applicable to kinematically redundant manipulators without using joint torque sensors or wrist-mounted force/torque sensors. By using motor current measurements an estimation of the external forces acting on the manipulator can be obtained and allows for a compliant behavior. Joint friction effects are overcome by superposing an additional movement in the null-space of the end-effector task. This control scheme is applied to an industrial manipulator, namely a Stäubli TX90L mounted on a linear axis (constituting a redundant 7-DOF manipulator) and experimental results are provided.

22 June 2018 in IEEE Robotics and Automation Letters
Verified
Journal Article
Closed access
DKDominik Kaserer
Dominik Kaserer
HGHubert Gattringer
Hubert Gattringer
AMAndreas Mueller
Andreas Mueller
This letter presents a new approach to online synchronization of a robot to the motion of an object. This is done by an iterative trajectory planning approach. Trajectory planning is divided into geometric path planning and subsequent time optimal parameterization of the geometric path. The geometric path planning approach can handle position constraints in joint space as well as in task space and results in a sequential quadratic program in two variables for each joint. The time optimal path parameterization respecting joint velocity, acceleration, and jerk constraints is formulated as a linear program. However, the overall optimization problem is nonlinear. Only few iterations of this nonlinear optimization problem can be performed online. Therefore, a method for obtaining a time scaling function is presented such that the robot and the object are synchronized exactly. The synchronization task is executed online and experimental results are shown for a 6-DOF manipulator.

17 December 2018 in Proceedings in Applied Mathematics and Mechanics
Verified
Journal Article
Open access
PDF file
DKDominik Kaserer
Dominik Kaserer
HGHubert Gattringer
Hubert Gattringer
AMAndreas Müller
Andreas Müller
A recent development for programming industrial robotic manipulators is the interactive teaching of task motions where a human operator physically guides the end‐effector of a robot. Admittance control schemes are used to this end. Since the operator is in direct contact with the robot, it must be ensured that the velocities of the robot are within a safe range at any time. Thus, in order to guarantee safe operation, position and velocity limits must be respected within the admittance control. Existing admittance control schemes can either take task space limits or joint space limits into account. In this paper an extended admittance control scheme is presented which is capable of simultaneously taking task space limits as well as joint space limits into account. This is achieved by formulating the admittance control law in terms of a path parameter to account for task space limits and a subsequent determination of the path parameter dynamics with respect to the joint space limits. Admittance control requires an estimation of the interaction wrench to be available. Three different methods for obtaining such an estimation are presented: 1) A six‐axis force/torque sensor mounted on the robot end‐effector, 2) The generalized momentum, 3) A decoupled mechanical model of the motors. The performance of the algorithms is demonstrated by means of experimental results.