6 February 2004 in IEEE Journal of Solid-State Circuits
Known elementary wide-band amplifiers suffer from a fundamental tradeoff between noise figure (NF) and source impedance matching, which limits the NF to values typically above 3 dB. Global negative feedback can be used to break this tradeoff, however, at the price of potential instability. In contrast, this paper presents a feedforward noise-canceling technique, which allows for simultaneous noise and impedance matching, while canceling the noise and distortion contributions of the matching device. This allows for designing wide-band impedance-matching amplifiers with NF well below 3 dB, without suffering from instability issues. An amplifier realized in 0.25-/spl mu/m standard CMOS shows NF values below 2.4 dB over more than one decade of bandwidth (i.e., 150-2000 MHz) and below 2 dB over more than two octaves (i.e., 250-1100 MHz). Furthermore, the total voltage gain is 13.7 dB, the -3-dB bandwidth is from 2 MHz to 1.6 GHz, the IIP2 is +12 dBm, and the IIP3 is 0 dBm. The LNA drains 14 mA from a 2.5-V supply and the die area is 0.3/spl times/0.25 mm/sup 2/.
1 January 1992 in IEEE Journal of Solid-State Circuits
CMOS circuits for integrated analog filters at very high frequencies, based on transconductance-C integrators, are presented. First a differential transconductance element based on CMOS inverters is described. With this circuit a linear, tunable integrator for very-high-frequency integrated filters can be made. This integrator has good linearity properties and nondominant poles in the gigahertz range owing to the absence of internal nodes. The integrator has a tunable DC gain, resulting in a controllable integrator quality factor. Experimental results of a VHF CMOS transconductance-C low-pass filter realized in a 3-¿m CMOS process are given. Both the cutoff frequency and the quality factors can be tuned. The cutoff frequency was tuned from 22 to 98 MHz and the measured filter response is very close to the ideal response of the passive prototype filter. Furthermore, a novel circuit for automatically tuning the quality factors of integrated filters built with these transconductors is describe
28 May 2008 in IEEE Journal of Solid-State Circuits
An inductorless low-noise amplifier (LNA) with active balun is proposed for multi-standard radio applications between 100 MHz and 6 GHz. It exploits a combination of a common-gate (CGH) stage and an admittance-scaled common-source (CS) stage with replica biasing to maximize balanced operation, while simultaneously canceling the noise and distortion of the CG-stage. In this way, a noise figure (NF) close to or below 3 dB can be achieved, while good linearity is possible when the CS-stage is carefully optimized. We show that a CS-stage with deep submicron transistors can have high IIP2, because the nugsldr nuds cross-term in a two-dimensional Taylor approximation of the IDS(VGS, VDS) characteristic can cancel the traditionally dominant square-law term in the IDS(VGS) relation at practical gain values. Using standard 65 nm transistors at 1.2 V supply voltage, we realize a balun-LNA with 15 dB gain, NF < 3.5 dB and IIP2 > +20 dBm, while simultaneously achieving an IIP3 > 0 dBm. The best performance of the balun is achieved between 300 MHz to 3.5 GHz with gain and phase errors below 0.3 dB and plusmn2 degrees. The total power consumption is 21 mW, while the active area is only 0.01 mm2.
22 April 2010 in IEEE Journal of Solid-State Circuits
This paper presents a 10 bit successive approximation ADC in 65 nm CMOS that benefits from technology scaling. It meets extremely low power requirements by using a charge-redistribution DAC that uses step-wise charging, a dynamic two-stage comparator and a delay-line-based controller. The ADC requires no external reference current and uses only one external supply voltage of 1.0 V to 1.3 V. Its supply current is proportional to the sample rate (only dynamic power consumption). The ADC uses a chip area of approximately 115×225 μm2. At a sample rate of 1 MS/s and a supply voltage of 1.0 V, the 10 bit ADC consumes 1.9 μW and achieves an energy efficiency of 4.4 fJ/conversion-step.
15 December 2009 in IEEE Journal of Solid-State Circuits
This paper presents a 2.2-GHz low jitter sub-sampling based PLL. It uses a phase-detector/charge-pump (PD/CP) that sub-samples the VCO output with the reference clock. In contrast to what happens in a classical PLL, the PD/CP noise is not multiplied by N 2 in this sub-sampling PLL, resulting in a low noise contribution from the PD/CP. Moreover, no frequency divider is needed in the locked state and hence divider noise and power can be eliminated. An added frequency locked loop guarantees correct frequency locking without degenerating jitter performance when in lock. The PLL is implemented in a standard 0.18- ¿m CMOS process. It consumes 4.2 mA from a 1.8 V supply and occupies an active area of 0.4 × 0.45 mm2. With a frequency division ratio of 40, the in-band phase noise at 200 kHz offset is measured to be -126 dBc/Hz. The rms PLL output jitter integrated from 10 kHz to 40 MHz is 0.15 ps.