19 March 2024 in Advanced Engineering Materials
The densification and sintering of ceramics using microwaves is first reported in the mid‐1960s. Today, the reduced carbon footprint of this process has renewed interest as it uses less energy overall compared to conventional process heating/furnaces. However, scaling up and commercializing the microwave sintering process of ceramics remains a formidable challenge. As a contactless method, microwave sintering offers geometric flexibility over other field‐assisted sintering processes. Yet, the inability to address multiscale, multiphysics‐driven heterogeneities arising during microwave coupling limits discussions about a future scale‐up process. Herein, the case is made that unlike 60 years ago, new advances in multiscale computational modeling, materials characterization, control systems, and software open up new avenues for addressing these challenges. More importantly, the rise of additive manufacturing techniques demands the innovation of sintering processes in the ceramics community for realizing near‐net‐shaped and complex parts for applications ranging from medical implants to automotive and aerospace parts.
26 August 2024 in International Journal of Ceramic Engineering & Science
Binder jet additive manufacturing is well suited for fabricating large (order of cm) and geometrically complex ceramic preforms. However, the main challenge in producing ceramic oxide parts via binder jetting is the high‐temperature postprocess tasked with eliminating internal porosity to achieve full densities. In this work, we demonstrate the ability to produce oxide ceramic parts with desirable densities by sintering binder jetted preforms. We investigate the sintering behavior of binder jetted preforms composed of three oxide powders with distinct morphologies: ball‐milled alumina, gas‐atomized silica, and sintered‐agglomerated zirconia. We fabricate the preform samples using a commercial binder jetting system and a conventional die‐pressing technique to understand the effect of starting densities. Furthermore, we parametrize the heating profiles to understand the effect of sintering temperature, sintering duration, and heating rate on each powder's densification behavior, microstructure, and phase composition. Results show the relatively low starting densities within the binder jetted preforms caused the onset sintering temperature to be higher than what is documented in conventional sintering studies. As expected, we observed sintered densities increase with respect to sintering temperature and duration. These findings were utilized to downselect sintering parameters capable of achieving high densities (>96%). Herein, this study validates the sintering of binder jetted preforms as a suitable way to manufacture ceramic parts, regardless of powder morphologies, thereby increasing the robustness of the supply chain involved in additive manufacturing of ceramic oxides.
27 September 2021 in Research Square
Electric vehicles (EVs) are in the incipient stage today and have the capacity to lead the automobile sector in the future. Battery packs of an electric vehicle are held by a large battery housing located at the bottom of the car body. The battery pack contributes significantly to the vehicle’s overall weight. Reduction of the overall weight of the future cars is a designer’s priority today. The aim to reduce weight can be achieved using topological optimisation. The optimised design is complex and therefore requires freeform fabrication. Additive manufacturing (AM) or 3D printing allows the fabrication of complex structures, hence, enables the fabrication of topological optimised parts without compromising on the part performance. In this paper, the topological optimisation of an electric vehicle battery housing is carried out to reduce the weight of the housing. Certain parts of the battery housing are removed and modified to get the final design. The physical, geometric, and performance aspects of the re-designed and original battery housing are compared. Additionally, the feasibility of the fabrication of the re-designed battery housing is discussed through support structures generation and feasibility index. Different AM methods such as powder bed fusion (PBF) and directed energy deposition (DED) are analysed on the basis of advantages and limitations. Finally, a suitable AM technique, selective laser melting (SLM), is chosen to fabricate the topological optimised battery housing.
26 March 2026 in Journal of the American Ceramic Society
Microwave (MW) sintering offers an energy‐efficient approach for densifying Al 2 O 3 ceramics. However, its adoption for ceramics 3D‐printed via binder‐jetting remains limited due to uneven heating, particularly in complex geometries. SiC susceptors improve thermal uniformity, but induce charge concentration and local hotspots, requiring careful control. Here, multiphysics models are combined with experiments to control hotspots and uniformly sinter binder‐jetted Al 2 O 3 using 2.45 GHz MWs. We developed electromagnetic wave‐heat transfer models to investigate how SiC susceptor configurations influence Al 2 O 3 heating. Simulations revealed that hexagonal configuration minimized sample temperature non‐uniformity (∼20°C), while square configuration suppressed localized hotspots. With reduced overheating, we experimentally sintered binder‐jetted blocks across 1300°C–1500°C, achieving ∼75%–86% relative density with microstructures and α‐alumina phases similar to conventional sintering, while at 1500°C shrinkage (∼65%–66%) was also comparable, reducing hold time from 6 h to 7.5 min. Extending to complex geometries, we applied the optimized process to evenly heat and sinter binder‐jetted spur gears, widely used in aerospace, achieving mechanical strength (∼54 N tooth‐failure load and ∼24.5 MPa maximum bending stress) comparable to its conventional counterpart (∼50 N tooth‐failure load in our study and ∼24.5 MPa bending stress reported in prior studies). Unlike previous MW sintering studies, the results enable uniform, hotspot‐controlled MW sintering of 3D‐printed ceramics. The ∼48x faster processing and ∼96% lower energy use than conventional, reinforces it as a scalable, electrified route for high‐throughput, decarbonized ceramic manufacturing.
28 August 2024 in The International Journal of Advanced Manufacturing Technology
Variability in the inherently dynamic nature of additive manufacturing introduces imperfections that hinder the commercialization of new materials. Binder jetting produces ceramic and metallic parts, but low green densities and spreading anomalies reduce the predictability and processability of resulting geometries. In situ feedback presents a method for robust evaluation of spreading anomalies, reducing the number of required builds to refine processing parameters in a multivariate space. In this study, we report layer-wise powder bed semantic segmentation for the first time with a visually light ceramic powder, alumina, or Al2O3, leveraging an image analysis software to rapidly segment optical images acquired during the additive manufacturing process. Using preexisting image analysis tools allowed for rapid analysis of 316 stainless steel and alumina powders with small data sets by providing an accessible framework for implementing neural networks. Models trained on five build layers for each material to classify base powder, parts, streaking, short spreading, and bumps from recoater friction with testing categorical accuracies greater than 90%. Lower model performance accompanied the more subtle spreading features present in the white alumina compared to the darker steel. Applications of models to new builds demonstrated repeatability with the resulting models, and trends in classified pixels reflected corrections made to processing parameters. Through the development of robust analysis techniques and feedback for new materials, parameters can be corrected as builds progress.