Oleksandr Terletskyi

Oleksandr Terletskyi

Auto-generated profile, based on publicly available information

Oleksandr Terletskyi

National Technical University “Kharkiv Polytechnic Institute

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

22 September 2025 in Collection of scientific works of the Ukrainian State University of Railway Transport
Verified
Journal Article
Open access
SKSergey Knyazev
Sergey Knyazev
HKHanna Kniazieva
Hanna Kniazieva
MPMykola Pohribnyi
Mykola Pohribnyi
OTOleksandr Terletskyi
Oleksandr Terletskyi
The article deals with aspects of improving the efficiency of boron and siliconization in the context of reducing the process duration and porosity. Promising compositions of pastes for saturation with boron and silicon are shown. The microstructures of a single-phase boron layer and a silicide layer on low-alloy steel are demonstrated. The highest porosity with signs of delamination is observed in the sample of boron from the paste 75 % B4C + 9.75 % NaF + 10 % B + 3.5 % Cu2O + 1.5 % NH4Cl, to a lesser extent, porosity is characteristic of layers on samples of boron from 65 % B4C + 35 % CuCl2; 75 % B4C + 10 % NaF + 5 % Cu2O + 10 % NH4Cl; 75 % B4C + 10 % NaF + 5 % CuCl2 + 10 % Al(OH)3. The thickness of the diffusion layer on the boron sample from the paste of 5 % B4C + 9.75 % NaF + 10 % B + 3.5 % Cu2O + 1.5 % NH4Cl is approximately 200 μm. On the sample of boron from 6 5% B4C + 35 % CuCl2 paste, the layer thickness ranges from 100 to 150 microns, the layer thickness obtained by boron from 75 % B4C + 10 % NaF + 5 % Cu2O + 10 % NH4Cl paste is 100 microns with the exit of individual needles into the main structure of the metal by another 50 microns. The thickness of the layer obtained by boronizing from a paste of 75 % B4C + 10 % NaF + 5 % CuCl2 + 10 % Al(OH)3 ranged from 200 to 150 microns. By instrumental indentation, the hardness, HI = 14.57 GPa, Young's modulus E = 293 GPa and crack resistance K1c = 10.75 MPa*m1/2 of the single-phase boron layer were determined. The implemented siliconization, obtained at saturation from industrial silicon, with the addition of 5 % (w/w) ammonium chloride and 20 % inert filler (merlins), allows to obtain a thick (200 μm) low-porous layer within 5 hours of processing with a microhardness of silicide on the surface of H100 of 25185 MPa. When using a fine fraction of silicon (30 μm), sintering of the crust on the surface was observed due to the intense silicon chloride transfer reaction and the accumulation of atomic silicon on the surface. The diffusion outflow of silicon deep into the material decreases, which also contributes to the formation of a sintered crust. Increasing the silicon grain size to 150 microns eliminates the problem of crusting, but some sintered silicon grains are still present on the surface.

11 December 2023 in Collection of scientific works of the Ukrainian State University of Railway Transport
Verified
Journal Article
Open access
PDF file
EZEduard Zozulya
Eduard Zozulya
АЗАнатолій Іванович Зубков
Анатолій Іванович Зубков
OTOleksandr Terletskyi
Oleksandr Terletskyi
VRValentin Riaboshtan
Valentin Riaboshtan
ВРВалентин Анатолійович Рябоштан
Валентин Анатолійович Рябоштан
In the scientific and technical literature review, investigated the use of niobium as an environmentally friendly and effective alloying addition to enhance the temperature stability of the structure and properties of copper products with an ultrafine-grained structure has been investigated. Considerable attention is paid to the potential of niobium as an alloying addition in the context of the innovative use of niobium to form a special «layer» at grain boundaries to strengthen its influence on the structure, especially the grain structure, and consequently on the properties of copper and materials based on it. The review of literature and informational sources devoted to the Cu-Nb phase diagram has shown that niobium is one of the most effective segregants to limit grain growth in binary copperbased alloys. Additionally, the efficiency of niobium as an alloying element that improves the grain structure and the mechanisms believed to underlie this phenomenon have been discussed. In particular, the use of alloying and liquid metal processing technologies for refining the grain structure of copper alloys has been examined. It has been elucidated that niobium in copper-based alloys is also used to enhance physicalmechanical and technological properties. The impact of microimpurities on the final structure of the copper-niobium alloy has been highlighted, imposing specific requirements on the purity of input materials and the technologies used to eliminate contamination from the melt and improve its homogenization. The review briefly discusses other methods that can be employed to form a special «layer» at grain boundaries. Specifically, technologies of mechanical alloying and methods of simultaneous deposition of component vapors in a vacuum have been studied. Based on the results of the literature analysis, the considerable prospectiveness of methods involving the simultaneous deposition of component vapors in a vacuum to create a special «layer» at grain boundaries has been demonstrated. The article examines the results of studies on niobium segregation at grain boundaries in the copper-niobium system and similar systems, establishing that the improvement of several described technologies and methods can be quite promising for the further development of technology for its implementation in production. У науково-технічному літературному огляді досліджено використання ніобію як екологічно безпечної та ефективної легуючої добавки для підвищення температурної стабільності структури і властивостей мідних виробів з ультрадрібнистою зеренною структурою. Значна увага приділена потенціалу ніобію як легуючої добавки в контексті інноваційного використання ніобію для утворення особливого «шару» на межах зерен з метою посилення його впливу на структуру, особливо зеренну, і відповідно властивості міді та матеріалів на її основі. Огляд літературних та інформаційних джерел, присвячених фазовій діаграмі Cu-Nb, показав, що ніобій є одним з найбільш сильнодіючих сегрегантів для обмеження зростання зерен у бінарних сплавах на основі міді. Крім того, розглянуто ефективність ніобію як легуючого елементу, що покращує зеренну структуру, і механізми, що, як вважається, лежать в основі цього явища. Зокрема, було розглянуто використання легування і технологій і методів обробки рідкого металу для подрібнення зеренної структури сплавів міді. З’ясовано, що ніобій у сплавах на мідній основі використовується також для поліпшення фізико-механічних і технологічних властивостей. Висвітлено вплив мікродомішок на кінцеву структуру сплаву мідь-ніобій, що стосується певних вимог до чистоти вхідних використовуваних матеріалів і технологій, з метою усунення забруднення розплаву та поліпшення його гомогенізації. В огляді стисло розглянуто й інші методи, які можна використати для утворення особливого «шару» на межах зерен. Зокрема, було вивчено технології механічного легування та методи одночасного осадження пари компонентів сплаву у вакуумі. На підставі результатів літературного аналізу показана значна перспективність методів одночасного осадження пари компонентів сплаву у вакуумі для створення особливого «шару» на межах зерен. У статті розглянуто результати досліджень сегрегації ніобію на границях зерен системи мідь-ніобій та інших подібних систем, внаслідок чого...


13 March 2026 in Bulletin of the National Technical University «KhPI». Series: Automobile and Tractor Construction
Verified
Journal Article
Open access
PDF file
OVOleh Volkov
Oleh Volkov
VSValeriіa Subbotinа
Valeriіa Subbotinа
MPMykola Pohribnyi
Mykola Pohribnyi
OTOleksandr Terletskyi
Oleksandr Terletskyi
AYAnastasiia Yushko
Anastasiia Yushko
ГФГанна Федоренко
Ганна Федоренко
The influence of the deformation component on the structural state and properties of steels during the process of additional friction-deformation strengthening (AFDS) has been investigated. It is known that during FDS, the simultaneous action of thermal flows and mechanical loads creates a complex stress–strain state in the near-surface layers of the material. The combination of thermal and mechanical energy causes intensive structural transformations manifested in the formation of fine-grained or even nanostructured regions, the development of deformation texture, and changes in phase composition.Special attention in the study is given to the role of elastic and plastic deformation in the strengthening mechanisms. Elastic deformation, although it does not leave permanent structural changes, determines the distribution of instantaneous stresses in the contact zone and influences the initiation of plastic shifts. Plastic deformation, which is dominant during AFDS, leads to the accumulation of dislocations, the formation of subgrains, and an increase in the defectiveness of the crystal lattice. These processes ensure a significant increase in microhardness and the development of a strengthened layer with improved mechanical characteristics.Using durometric examinations, as well as previously obtained metallographic analysis data, the relationship between microstructural evolution and changes in material properties under the action of deformation has been established. The results of microhardness measurements are presented, and the influence of the deformation component on its distribution across the cross-section of steel specimens with different carbon contents is analyzed. It is shown that an increase in the proportion of plastic deformation promotes the formation of a deeper and more uniform strengthened layer, while the ratio of elastic to plastic deformation determines the hardness gradient and structural heterogeneity within the zone affected by AFDS.