Anion-exchange membrane fuel cells and Zn–air batteries based on non-Pt group metal catalysts typically suffer from sluggish cathodic oxygen reduction. Designing advanced catalyst architectures to improve the catalyst’s oxygen reduction activity and boosting the accessible site density by increasing metal loading and site utilization are potential ways to achieve high device performances. Herein, we report an interfacial assembly strategy to achieve binary single-atomic Fe/Co-Nx with high mass loadings through constructing a nanocage structure and concentrating high-density accessible binary single-atomic Fe/Co–Nx sites in a porous shell. The prepared FeCo-NCH features metal loading with a single-atomic distribution as high as 7.9 wt% and an accessible site density of around 7.6 × 1019 sites g−1, surpassing most reported M–Nx catalysts. In anion exchange membrane fuel cells and zinc–air batteries, the FeCo-NCH material delivers peak power densities of 569.0 or 414.5 mW cm−2, 3.4 or 2.8 times higher than control devices assembled with FeCo-NC. These results suggest that the present strategy for promoting catalytic site utilization offers new possibilities for exploring efficient low-cost electrocatalysts to boost the performance of various energy devices.
18 August 2017 in Journal of Materials Chemistry A
Doped nanocarbon materials (e.g., carbon nanotubes, graphene) are considered as effective electrocatalyst supports for fuel cells, and their electrochemical properties are closely related to the synthetic methods and the types of doping elements. In the current paper, we report a novel approach to synthesize sulfur-doped multi-walled carbon nanotubes (S-MWCNTs) as a highly efficient support material for Pt nanoparticle catalysts. The S-MWCNTs are obtained by annealing poly(3,4-ethylenedioxythiophene) (PEDOT) functionalized multi-walled carbon nanotubes at 800 °C. The prepared nanohybrids were physically characterized by Raman spectroscopy, Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). It has been found that the doping of sulfur into MWCNTs could significantly improve the dispersion of supported Pt nanoparticles of 2.37 nm in size and increase the electrochemically active surface area (ECSA, 161.4 m2 g−1). The doped sulfur atoms not only provide uniformly dispersed anchoring sites for the deposition of Pt nanoparticles on the surface of MWCNTs but also enhance the electron transfer interaction between Pt nanoparticles and the S-MWCNT support. The electrochemical properties of the catalysts were evaluated by using cyclic voltammetry (CV) and chronoamperometry (CA) techniques. The results demonstrate that the as-prepared Pt/S-MWCNTs exhibit much higher electrocatalytic activity, long-term durability and CO-tolerance ability for the methanol oxidation reaction (MOR) compared to the undoped MWCNT supported Pt and commercial Pt/C catalysts.
A novel nanostructured catalyst of platinum nanoparticles supported on 5,10,15,20-tetrakis(1-methyl-4-pyridinio)porphyrin tetra(p-toluenesulfonate) (TMPyP) functionalized graphene (TMPyP-graphene) is synthesized by the hydrothermal polyol process. The as-synthesized nanocomposites are characterized by Fourier transform infrared (FTIR) spectroscopy, UV-vis absorption spectroscopy, Raman spectroscopy, X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and electrochemical tests. It has been found that Pt nanoparticles of ca. 3.4 nm are uniformly dispersed on the surface of TMPyP-graphene, and hold a high electrochemical active surface area (ECSA) of 126.2 m2 g−1. The results demonstrate that the Pt/TMPyP-graphene catalyst exhibits a much higher electrocatalytic activity and stability than the Pt/graphene and commercial Pt/C catalysts for methanol oxidation, which is of significant importance in improving the efficiency of Pt-based electrocatalysts for DMFCs applications.
9 August 2022 in Journal of Colloid and Interface Science