28 December 2023 in Chemical Engineering Research and Design
MBMuhammad Yusuf Bakhtiar
1 August 2018 in Journal of Molecular Liquids
12 July 2017 in Journal of Chemical & Engineering Data
1 April 2020 in IOP Conference Series: Materials Science and Engineering
Natural gas is used as fuel in industries, power plants, commercial installations, and households. In its application, natural gas leaks can be considered as a major hazard because of its flammable and explosive nature. In addition to fuel, heat and oxygen sources, fires and explosions can occur if the concentration of natural gas in the air is between Low Flammable Limit (LFL) and Upper Flammable Limit (UFL). If the release of natural gas is not ignited, it will immediately form a Vapor Cloud Explosion (VCE) that can cause an explosion if it meets ignition point. Therefore, a research on dispersion patterns in a particular area or space is needed to minimize hazards and to develop safety procedures and regulations. This research aims to determine the external parameters that affect the dispersion and explosion caused by natural gas by using FLACS software from PT. Gexcon Indonesia. This software can display overpressure graphs of time and 3D visuals of simulations. The external parameters consist of vent size (5.4 m2 and 2.7 m2), wind direction, lighter position (center and back), day and night condition, and the presence of a obstacle (with and without obstacle). From the research results by the simulations, it is obtained that the highest overpressure value when there is an obstacle with a vent size of 2.7 m2; wind direction from the north; night condition, and back ignition point is 0.503 bars at 40, 835 s which can cause most buildings to collapse and the death rate to increase.
29 April 2023 in ASEAN Journal of Chemical Engineering
Heat recovery is considered as the key to improve energy efficiency in the process design. An appropriate heat exchanger network (HEN) design is an effective tool to maximize heat recovery from the process streams and to minimize energy consumption. The objectives of this study were arranging optimum HEN based on the annual cost in the power industry. HEN in the Paiton Steam Power Plant, East Java, Indonesia, was designed using spreadsheet and Aspen Energy Analyzer with Peng-Robinson equation. Pinch analysis was conducted by comparing Tmin (10°C - 19°C) to obtain Maximum Energy Recovery (MER) and Heat Exchanger Area (HEA). The HEN design was optimized using grid diagram. Simulation in this study succeeded to reduce the annual cost the most effectively at ∆Tmin 16°C. This design optimized the process integration and contributed to the capital, operation, and total annual cost reduction of 14.3%. The maximum energy recovery was 286,706 kW and HEA 138.790 m2. This result is a solution for Steam Power Plant as an effort for enhancing energy efficiency and the company competitiveness.
1 June 2019 in IOP Conference Series: Materials Science and Engineering
Light naphtha is not reliable used as automotive fuel because of its low octane number (RON) and high vapor pressure. To utilize light naphtha as fuel, blending process may be used to obtain usable gasoline fuel. Diethyl carbonate (DEC) can be used as blending agent with light naphtha because its high octane number and low vapor pressure. Therefore in this work, the vapor pressure and octane number (RON) of DEC–light naphtha blends were measured to study the effect of DEC in light naphtha blending. The vapor pressure measurements show that vapor pressure of DEC–light naphtha blends decreased while the DEC fraction increased. The pseudo binary analysis approachment was used to correlate the vapor pressure experimental data and predict the vapor pressure of light naphtha + DEC blends. The Wilson and nonrandom two-liquid (NRTL) model are giving good correlation and prediction result with average absolute deviation (AAD) less than 1.3% meanwhile the Hildebrand & Scatchard model give quietly poor result with AAD value of 4.4%. The RON measurements show that the RON values of the blends increased while the DEC fraction increased. The DEC is successfully used as blending agent into light naphtha with 30% v/v optimum fraction.