Estimating transportation network emissions requires multiplying estimates of on-road vehicle activity (by source type and operating mode) by applicable emission rates for the observed source type and operating conditions. Coupling microsimulation model runs with emissions modeling can make fast assessments possible in transportation air quality planning. This research developed a tool with automated linkage between the Vissim microsimulation model and the Motor Vehicle Emission Simulator (MOVES) model. To link the two models, the research team used MOVES-Matrix, which was prepared by iteratively running MOVES across all possible iterations of vehicle source type, fuel, environmental and operating conditions, and other parameters (hundreds of millions of model runs) to create a multidimensional emission rate lookup matrix. A Vissim simulation of the major arterial roads and freeways at I-85 and Jimmy Carter Boulevard in Gwinnett County, Georgia, provided the case study for this MOVES-matrix application. The researchers present predicted emissions and the results of a sensitivity analysis to identify the potential impacts of various internal Vissim modeling parameters (such as minimum headway, maximum deceleration rate for cooperative braking, and emergency stop distance) on a case study’s emissions outputs. The sensitivity analysis found that internal Vissim parameters impacted emissions and that proper care should be taken in using Vissim for emissions analysis at the corridor and link level. The case study demonstrates that Vissim coupled with MOVES-Matrix can be an effective tool for emissions analysis.
14 April 2017 in Journal of the Air & Waste Management Association
MOVES and AERMOD are the U.S. Environmental Protection Agency’s recommended models for use in project-level transportation conformity and hot-spot analysis. However, the structure and algorithms involved in running MOVES make analyses cumbersome and time-consuming. Likewise, the modeling setup process, including extensive data requirements and required input formats, in AERMOD lead to a high potential for analysis error in dispersion modeling. This study presents a distributed computing method for line source dispersion modeling that integrates MOVES-Matrix, a high-performance emission modeling tool, with the microscale dispersion models CALINE4 and AERMOD. MOVES-Matrix was prepared by iteratively running MOVES across all possible iterations of vehicle source-type, fuel, operating conditions, and environmental parameters to create a huge multi-dimensional emission rate lookup matrix. AERMOD and CALINE4 are connected with MOVES-Matrix in a distributed computing cluster using a series of Python scripts. This streamlined system built on MOVES-Matrix generates exactly the same emission rates and concentration results as using MOVES with AERMOD and CALINE4, but the approach is more than 200 times faster than using the MOVES graphical user interface. Because AERMOD requires detailed meteorological input, which is difficult to obtain, this study also recommends using CALINE4 as a screening tool for identifying the potential area that may exceed air quality standards before using AERMOD (and identifying areas that are exceedingly unlikely to exceed air quality standards). CALINE4 worst case method yields consistently higher concentration results than AERMOD for all comparisons in this paper, as expected given the nature of the meteorological data employed. Implications: The paper demonstrates a distributed computing method for line source dispersion modeling that integrates MOVES-Matrix with the CALINE4 and AERMOD. This streamlined system generates exactly the same emission rates and concentration results as traditional way to use MOVES with AERMOD and CALINE4, which are regulatory models approved by the U.S. EPA for conformity analysis, but the approach is more than 200 times faster than implementing the MOVES model. We highlighted the potentially significant benefit of using CALINE4 as screening tool for identifying potential area that may exceeds air quality standards before using AERMOD, which requires much more meteorology input than CALINE4.
20 September 2018 in Transportation Research Record: Journal of the Transportation Research Board
The MOVES (MOtor Vehicle Emissions Simulator) model was developed by the U.S. Environmental Protection Agency (USEPA) to estimate emissions from mobile sources and is required to be used for regional air quality planning and conformity analysis in all states except California. However, the MOVES interface is complicated, and assessing emissions from dynamic large-scale transportation networks can be difficult. To aid in these analyses, the MOVES-Matrix modeling tool was developed as an alternative to the direct application of the MOVES model. MOVES-Matrix employs a massive multidimensional array of MOVES outputs created by running MOVES with every allowable combination of input variables. Once this output array has been generated, subsequent energy and emissions analyses can be conducted quickly and dynamically. Until recently, MOVES-Matrix has only been used to analyze running exhaust. In this study, MOVES-Matrix has been used expanded to include emissions from engine starts, truck hoteling, evaporative sources, and brake/tire wear as well as running exhaust. A case study is conducted for the metropolitan Atlanta, GA to verify the feasibility of using this expanded version of MOVES-Matrix and to ensure that the approach obtains the exact same results as applying MOVES directly. The travel activity inputs come from regional travel data generated by the Atlanta Regional Commission’s Travel Demand Model. The emission results from MOVES-Matrix were compared with MOVES output to verify the equivalence of this approach.
1 March 2022 in Research in Transportation Economics