20 October 2016 in Journal of Lightwave Technology
We report a 5-mode erbium doped fiber amplifier (EDFA) operating in the L-band (1570-1605 nm) designed to extend the bandwidth of mode division multiplexed transmission. We design an EDF with a center depressed core index and a ring doped erbium concentration profile to obtain a low differential modal gain (DMG) and a low splice loss with a graded-index fiber as a transmission line. Then we fabricate a center depressed core EDF and realize a gain of 20 dB for all modes and a low DMG with a deviation of less than 3 dB in the 1570 – 1605 nm range with a 48-m-long erbium doped fiber when the pump mode is the LP01 mode.
30 January 2018 in Journal of Lightwave Technology
We demonstrate a ring resonator based gain-clamped 4-LP-mode erbium-doped fiber amplifier (EDFA). In this study, we show that a gain-clamped EDFA can reduce temporal modal gain variation simultaneously in all modes. We experimentally evaluate the transient response of a 4-LP-mode EDFA and succeed in reducing the modal gain variation for all modes at 1530 and 1550 nm from 4.0 to 1.1 dB and from 2.8 to 0.7 dB, respectively, by using a gain-clamping technique.
29 September 2017 in Journal of Lightwave Technology
We report the design, fabrication and evaluation of a cladding pumped 2-LP mode 6-core moderately coupled amplifier. In this study, we show that moderately coupled multi-core erbium doped fiber (EDF) can realize a high pump power density in a cladding by allowing core-to-core power coupling. We also experimentally evaluate the amplification characteristics and confirm an average mode-core gain of 18 dB, a differential mode-core gain of 4 dB, and an average noise figure of 7 dB in the C-band. Moreover, we confirm an average mode-core gain of 15 dB, a differential mode-core gain of 5 dB, and an average noise figure of 7.5 dB in the L-band.
12 December 2016 in Journal of Lightwave Technology
We investigate a coupled few-mode multi-core fiber (FM-MCF) design to realize an ultra-high spatial density space division multiplexing (SDM) transmission line with low differential mode delay (DMD) characteristics. We describe a super-mode-based FM-MCF design that takes account of the DMD between modes in the inter-LP mode group (e.g. between LP01- and LP11-like super-modes). We also show a randomly coupled FM-MCF design based on fiber bending and twisting to reduce the DMD between modes in the intra-LP mode group. We fabricated coupled 3-mode 7-core fiber and realized a low DMD value of less than 0.2 ns/km for all modes where the inter-core non-uniformity induced DMD was successfully suppressed owing to distributed random mode coupling. The fabricated fiber has 21 spatial modes within a 125 mm cladding, and a relative core density of 21, which is the highest of any reported 125 mm cladding SDM fiber.
7 November 2013 in Optical Fiber Technology
We propose a WDM MIMO system that uses a selective mode excitation technique to reduce MIMO DSP over a conventional GI-MMF. We show numerically that we can selectively excite low-order modes with the small DMD of GI-MMF and confirm experimentally that we can obtain a small DMD over a wide wavelength range under selective mode excitation conditions. We realize a C- and L-band WDM coherent optical 2 × 2 MIMO transmission over a 10-km 50 μm-core GI-MMF, which enables us to reduce MIMO DSP complexity over a wide wavelength range.
1 February 2017 in Journal of Lightwave Technology
We propose a strongly coupled ring core fiber for mode-division multiplexed (MDM) transmission with multiple-input multiple-output (MIMO) digital signal processing (DSP) supporting two linearly polarized (LP) modes over the C-band. We show numerically that the mode coupling efficiency of ring-core fiber can be increased by optimizing the structural parameters of the fiber based on an S-bend model. Accordingly, the coupling coefficient is successfully controlled using ring-core fiber fabricated with an effective index difference between the modesneff of 0.3 × 10-3 and an effective area Aeff of 290 m2 for the LP01 and LP11 modes. Finally, we experimentally demonstrate the applicability of our fiber to MDM transmission with MIMO DSP and successfully reduce the signal quality difference by employing mode coupling in a fabricated 15.4 km fiber.