Ting Xu

Ting Xu

Auto-generated profile, based on publicly available information

Ting Xu

College of Field Engineering, Army Engineering University of PLA , Nanjing 210007, Jiangsu

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 November 2022 in Polymers
Verified
Journal Article
Open access
PDF file
TXTing Xu
Ting Xu
ZQZehao Qi
Zehao Qi
QYQin Yin
Qin Yin
YJYumin Jiao
Yumin Jiao
LALizhou An
Lizhou An
YTYefa Tan
Yefa Tan
In order to improve the interface and mechanical properties of aramid fiber (AF)-reinforced epoxy resin (EP) composites (AF/EPs), the surface modification of AF was carried out with atmospheric pressure air plasma, and the effects of plasma treatment time and discharge power on the AF surface and the interface and mechanical properties of AF/EPs were investigated. The results show that, when plasma treatment time was 10 min and discharge power was 400 W, AF showed the best modification effect. Compared to the unmodified material, the total content of active groups on the surface of AF increased by 82.4%; the contact angle between AF and EP decreased by 20%; the interfacial energy and work of adhesion increased by 77.1% and 19.1%, respectively; the loss of AF monofilament tensile strength was controlled at only 8.6%; and the interlaminar shear strength and tensile strength of AF/EPs increased by 45.5% and 10.4%, respectively. The improvement in AF/EP interfacial and mechanical properties is due to the introduction of more active groups on the AF surface with suitable plasma processing parameters, which strengthens the chemical bonding between the AF and EP matrix. At the same time, plasma treatment effectively increases the surface roughness of AF, and the mechanical meshing effect between the AF and EP matrix is improved. The synergistic effect of chemical bonding and mechanical meshing improves the wettability and interfacial bonding strength between the AF and EP matrix, which enables the load to be transferred from the resin to the fiber more efficiently, thereby improving the mechanical properties of the AF/EP.

29 September 2022 in ACS Omega
Verified
Journal Article
Open access
TXTing Xu
Ting Xu
JTJin Tian
Jin Tian
LALizhou An
Lizhou An
YJYumin Jiao
Yumin Jiao
QYQin Yin
Qin Yin
YTYefa Tan
Yefa Tan

1 August 2011 in Transactions of Nonferrous Metals Society of China
Verified
Journal Article
Closed access
BCBin Cai
Bin Cai
YTYe-Fa Tan
Ye-Fa Tan
YTYi-Qiang Tu
Yi-Qiang Tu
XWXiao-Long Wang
Xiao-Long Wang
TXTing Xu
Ting Xu

1 October 2024 in AIP Advances
Verified
Journal Article
Open access
PDF file
TXTing Xu
Ting Xu
LALizhou An
Lizhou An
QYQin Yin
Qin Yin
YJYumin Jiao
Yumin Jiao
YZYou Zhou
You Zhou
YTYefa Tan
Yefa Tan
To address the need for rapid in situ plugging and repair of hydraulic machinery and chemical pipelines and to resolve the issue that a single curing agent cannot simultaneously achieve rapid curing and excellent mechanical properties in epoxy resin systems, this study explores the use of composite curing agents. In particular, effective formulations are designed for mixing fast and slow curing agents, studying their effects on the curing behavior, curing quality, and mechanical properties of epoxy resins and elucidating their influence mechanisms. The results indicate that three resin systems meet the requirements for rapid curing (curing time within 30 min): 4A6B/EP, 2A8B/EP, and 0A10B/EP. Among them, 4A6B/EP exhibits the best curing quality and mechanical properties. In particular, 4A6B/EP demonstrates the lowest values of curing shrinkage rate, internal curing stress, average pore size, porosity, and cumulative pore volume. Its low internal stress and low defects reduce the stress concentration, while more efficient deflection and branching of internal cracks enhance its deformation resistance. Consequently, 4A6B/EP shows the highest microhardness, fracture toughness, tensile strength, Young’s modulus, and elongation after fracture. Based on the comprehensive evaluation of rapid curing characteristics and mechanical properties, the 4A6B/EP system offers the best overall performance. Therefore, it is recommended as the preferred resin system for rapid plugging and repair of composite materials, providing a theoretical basis and technical support for boosting the application of epoxy resin composite materials in high-tech fields.

1 May 2021 in Optical Fiber Technology
Verified
Journal Article
Closed access
ZSZhuocheng Shentu
Zhuocheng Shentu
JKJuan Kang
Juan Kang
ZZZhicheng Zhu
Zhicheng Zhu
LWLin Wang
Lin Wang
Yong GuoYong Guo
Yong Guo
CZChunliu Zhao
Chunliu Zhao

16 December 2023 in Polymers
Verified
Journal Article
Open access
PDF file
TXTing Xu
Ting Xu
YJYumin Jiao
Yumin Jiao
ZSZhenglian Su
Zhenglian Su
QYQin Yin
Qin Yin
LALizhou An
Lizhou An
YTYefa Tan
Yefa Tan
Phenyl polyhedral oligomeric silsesquioxane (POSS) is modified onto the GO surface by using the strong π–π coupling between a large number of benzene rings at the end of the phenyl POSS structure and the graphite structure in the GO sheet, realizing the non-covalent functionalization of GO (POSS-GO). The POSS-GO-reinforced EP (POSS-GO/EP) composite material is prepared using the casting molding process. The surface morphology of GO before and after modification and its peel dispersion in EP are examined. Furthermore, the mechanical properties, cross-sectional morphology, and reinforcement mechanism of POSS-GO/EP are thoroughly examined. The results show that the cage-like skeleton structure of POSS is embedded between the GO layers, increasing the spacing between the GO layers and leading to a steric hindrance effect, which effectively prevents their stacking and aggregation and improves the dispersion performance of GO. In particular, the 0.4 phr POSS-GO/EP sample shows the best mechanical properties. This is because, on the one hand, POSS-GO is uniformly dispersed in the EP matrix, which can more efficiently induce crack deflection and bifurcation and can also cause certain plastic deformations in the EP matrix. On the other hand, the POSS-GO/EP fracture cross-section with a stepped morphology of interlaced “canine teeth” shape is rougher and more uneven, leading to more complex crack propagation paths and greater energy consumption. Moreover, the mechanical meshing effect between the rough POSS-GO surface and the EP matrix is stronger, which is conducive to the transfer of interfacial stress and the strengthening and toughening effects of POSS-GO.