Daniel Kümmel

Daniel Kümmel

Auto-generated profile, based on publicly available information

Daniel Kümmel

Institute for Applied Materials IAM, Karlsruhe Institute of Technology KIT, Karlsruhe, Germany

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2019 in Wear
Verified
Journal Article
Closed access
DKDaniel Kümmel
Daniel Kümmel
MHMarcus Hamann-Schroer
Marcus Hamann-Schroer
HHHarald Hetzner
Harald Hetzner
JSJohannes Schneider
Johannes Schneider

1 October 2020 in Tribology International
Verified
Journal Article
Closed access
DKDaniel Kümmel
Daniel Kümmel
DLDominic Linsler
Dominic Linsler
RSReinhard Schneider
Reinhard Schneider
JSJohannes Schneider
Johannes Schneider

5 September 2020 in Tribology Letters
Verified
Journal Article
Open access
PDF file
DKDaniel Kümmel
Daniel Kümmel
JSJohannes Schneider
Johannes Schneider
PGPeter Gumbsch
Peter Gumbsch
Titanium alloys are used for their good mechanical and corrosion properties, but generally experience poor wear behavior. This can effectively be counteracted by a thermal oxidation treatment, reducing wear significantly. Employing a special sample preparation, we study the transition of tribological properties between thermally oxidized and bulk Ti6Al4V on a single sample. While oxygen signal intensity and hardness followed an exponential decay from the surface to bulk material, tribological results showed a step-like transition from low to high friction and wear with increasing distance from the surface. Low wear was associated with minor abrasive marks, whereas high wear showed as severe adhesive material transfer onto the steel counter body. Besides the mechanical property of hardness, also a change in fracture behavior by interstitial oxygen could influence the observed tribological behavior.

1 January 2018 in Procedia CIRP
Verified
Journal Article
Open access
ESEric Segebade
Eric Segebade
DKDaniel Kümmel
Daniel Kümmel
FZFrederik Zanger
Frederik Zanger
JSJohannes Schneider
Johannes Schneider
VSVolker Schulze
Volker Schulze

1 April 2017 in Wear
Verified
Journal Article
Open access
DLD. Linsler
D. Linsler
DKD. Kümmel
D. Kümmel
ENE. Nold
E. Nold
MDM. Dienwiebel
M. Dienwiebel
As thermal spray coated cylinder surfaces eliminate the need for cast iron sleeves or hypereutectic AlSi alloys, these coatings are becoming the main cylinder liner technology. Moreover, it has been found that these coatings also lead to low friction and wear. The reason for improved tribological performance is believed to result from a nanocrystalline layer that forms in the sliding contact. In this paper, we use on-line wear measurement to study the dynamics of the running-in process. A pin-on-disk tribometer coupled to a radionuclide wear measurement (RNT) system was used to investigate the friction and wear behavior of wire arc spray (LDS) coatings sliding against chromium coatings under lubricated conditions. After the friction experiments, X-ray photo electron spectroscopy (XPS) and Focused Ion Beam analysis (FIB) was used to characterize the worn surfaces. By introducing a time-dependent Stribeck plot, we analyzed running-in under constant and transient sliding c onditions and observed a strong reduction of friction in the boundary lubrication regime. Wear rates of the LDS disks as well as of the chromium plated pins are ultra-low. XPS revealed carbon diffusion at room temperature in wear tracks of disks that showed a very low coefficient of friction (CoF) of 0.01, whereas this carbon diffusion could not be detected in the wear track of a disk without running-in, i.e. a final CoF of 0.12. As this is the most significant difference found between differently run-in systems, the described carbon diffusion might be relevant for the observed friction behaviour. Running-in behaviour can only be discussed in terms of friction, as, even with RNT, no significant wear could be measured. The comparison of running-in under transient and constant conditions showed only minor differences in the final friction behavior

13 December 2018 in Procedia Manufacturing
Verified
Journal Article
Open access
PDF file
ESEric Segebade
Eric Segebade
DKDaniel Kümmel
Daniel Kümmel
FZFrederik Zanger
Frederik Zanger
JSJohannes Schneider
Johannes Schneider
VSVolker Schulze
Volker Schulze
The usability of Ti-alloys in tribological systems is limited due to high wear rates during sliding. Therefore, many parts of critical aircraft assemblies are built using steel instead. Empowering Ti-alloys to be used in tribological systems will therefore enable a significant reduction of weight in e.g. landing gears. Surface texturing is widely used to improve the tribological behavior of metal parts. Most texturing methods using cutting tools depend on chip formation as the primary mechanism of texturing. In this work, a chipless process of surface texturing titanium parts using a cutting tool is developed. To this end, the resulting texture geometry variance is analyzed regarding the process parameters. It could be demonstrated in selected tribological experiments, that the textured surfaces produced using the chipless process are far superior to textures produced by chip formation.