This paper proposes and evaluates an architecture for a low-power Time-to-Digital Converter (TDC) with high resolution, optimized for high-rate operation (40MSa/channel), and integration with analog front-end in multichannel readout chips in 130 nm CMOS technology. The converter is based on a three-step architecture. The first step uses a counter and the following ones are based on two types of Delay-Line (DL) structures. A programmable Time Amplifier (TA) is used between the second and third steps to reach a final resolution of 24.4 ps in the standard mode of operation. In addition, this architecture uses common continuously stabilized master blocks that control the channels against the effects of global Process, Voltage, and Temperature (PVT) variations. We also propose a per-channel DL gain correction based on a trimmable block to correct mismatch effect. The area of the TDC channel is only 0.051 mm 2 . For a 40MSa/channel rate, the TDC average power consumption measured per channel is 2.2 mW for a 100% hit occupancy and decreases to 311 μW for the 10% occupancy specified for our main application. The demonstrated compactness and low power consumption fully match our requirements for integration into multichannel front-end chips. The experimental results demonstrate good timing performance over a broad range of operating temperatures (-35°C and 65°C), which conforms to our expectations. For example, the measured timing integral nonlinearity is better than ±1 LSB (±25 ps), and the overall timing precision is better than 21 ps RMS.
A novel method to reconstruct the energy of hadronic showers in the CMS High Granularity Calorimeter (HGCAL) is presented. The HGCAL is a sampling calorimeter with very fine transverse and longitudinal granularity. The active media are silicon sensors and scintillator tiles readout by SiPMs and the absorbers are a combination of lead and Cu/CuW in the electromagnetic section, and steel in the hadronic section. The shower reconstruction method is based on graph neural networks and it makes use of a dynamic reduction network architecture. It is shown that the algorithm is able to capture and mitigate the main effects that normally hinder the reconstruction of hadronic showers using classical reconstruction methods, by compensating for fluctuations in the multiplicity, energy, and spatial distributions of the shower's constituents. The performance of the algorithm is evaluated using test beam data collected in 2018 prototype of the CMS HGCAL accompanied by a section of the CALICE AHCAL prototype. The capability of the method to mitigate the impact of energy leakage from the calorimeter is also demonstrated.
H2GCROC is a 130 nm CMOS ASIC designed to read out the SiPMs coupled to the scintillating tiles of the back hadronic sections of CMS HGCAL. Each of its 72 channels comprises a current conveyor, a high-gain preamplifier, a shaper, an ADC for energy measurement, and two discriminators linked to TDCs for capturing time-of-arrival and time-over-threshold information, respectively. This work presents the ASIC architecture and its characterization in the laboratory and test beam environments. The results demonstrate its adaptability in calibration, proving its capability to measure the SiPM single-photon spectrum and MIP's energy with high resolution under the expected radiation conditions during the entire operation of HGCAL.
Conception et caractérisation d’ASIC de lecture des détecteurs SiPM dans des mesures de temps pico-seconde pour l’expérience CMS HGCAL: Les ASIC HGCROC sont des composants électroniques frontaux dédiés, conçus pour lire le calorimètre à haute granularité (HGCAL), qui remplacera les calorimètres actuels du Grand collisionneur de hadrons (LHC) dans le cadre de la collaboration sur le solénoïde compact à muons (CMS). Ce travail met l'accent sur les caractéristiques spécifiques de la conception du HGCAL qui ont influencé la conception de l'ASIC de lecture du photomultiplicateur au silicium (SiPM).H2GCROC est un ASIC 130 nm CMOS conçu pour lire les SiPM couplés aux tuiles scintillantes des sections hadroniques arrière de CMS HGCAL. Le préamplificateur frontal à l'intérieur de la puce est adapté au niveau de signal plus élevé du SiPM, anticipant les pC par particule ionisante minimale (MIP) au lieu des gammes fC/MIP. Cette thèse présente l'architecture ASIC et sa caractérisation en laboratoire et en faisceau d'essai. Elle démontre une bonne adaptabilité dans l'étalonnage, la tolérance au rayonnement et la capacité de mesurer le spectre de photons uniques du SiPM et l'énergie du MIP avec une haute résolution. Ce travail illustre également les améliorations proposées, développées et testées entre la deuxième et la troisième version imprimée de l'ASIC et les changements futurs de la prochaine et dernière version de l'ASIC.