23 October 2019 in IEEE Transactions on Applied Superconductivity
13 December 2022 in Superconductor Science and Technology
ReBCO racetrack coils may be used in high-dynamic superconducting linear motor systems, typically replacing either permanent- or electromagnets in the DC stator. Even so, in order to achieve a significant increase in force density, the superconductor needs to carry a high transport current while simultaneously experiencing the time-varying magnetic field from the copper mover coils. To aid with the design of such devices, a 2D numerical model has been developed that predicts the AC loss under motor-relevant conditions, i.e. under the combined influence of a stationary transport current and an alternating external magnetic field. The main aim of the experiments described in this paper is to validate this model with dedicated AC loss measurements. To this end, we constructed a set-up that simultaneously measures magnetization-, transport current- and overall AC loss. Two identical insulated sub-scale ReBCO racetrack coils were tested at 4.2 K while carrying a stationary transport current of up to 700 A in a sinusoidal, alternating magnetic field up to 1.5 T, applied perpendicular to the broad face of the windings. Just like with metallic superconductors, the transport current significantly increases the AC loss level and lowers the penetration field. The inductive, electric and calorimetric data were found to be consistent with each other, validating the experimental calibration methods involved. Furthermore, the numerical model accurately predicted all AC loss components in the coils without any fitting to the data and can thus reliably be used in the design of superconducting machines.
22 February 2023 in IEEE Transactions on Applied Superconductivity
The ground-based Advanced Superconducting and Cryogenic Experimental power train Demonstrator (ASCEND) at Airbus intends to demonstrate the potential and feasibility of a cryogenic and superconducting powertrain as a breakthrough electric propulsion solution on future electric aircraft. A direct current distribution network is used in a propulsion chain to transfer 500 kW of power from the source to an electrical converter, which transforms the power into an alternating voltage/current to drive a superconducting motor. The working point of 1,700 A and 300 V is chosen for safety and installation reasons by operating at relatively low voltage. The direct current (DC) bus of ASCEND will be formed by a pair of high-temperature superconducting CORC ® cables inserted into a 10-meter-long narrow cryostat, resulting in a compact and lightweight solution. The 2-meter-long alternating current (AC) bus between the inverter and the electric motor is formed by a three-phase CORC ® cable. The challenge associated with 500 Hz operation in which a balance between AC loss in the cable and the size and mass of the system needs to be found, will be outlined. The AC and DC buses include several devices that connect the liquid nitrogen cooled power cables with the other system components that, in the case of the room temperature generator, operate at significantly higher temperatures. These devices thus include conduction-cooled current leads that are dimensioned to minimize the heat inleak from the warm to the cold environment. An overview of the design of the AC and DC buses and connecting devices will be provided and some of the design and operational challenges will be outlined.
27 February 2023 in Superconductor Science and Technology
No-insulation coils are self-protecting and can therefore generally be operated at higher current densities. However, the electrical turn-to-turn connections may cause additional AC loss when charging the coil or when it is exposed to a time-dependent magnetic field. In this work, we study the case of a no-insulation ReBCO tape racetrack coil exposed to a uniform AC field applied parallel to the tape surface. We show that an anisotropic continuum model allows to formulate analytical approximations for coupling loss in the low- and high-frequency limits. For intermediate frequencies, the continuum model needs to be evaluated numerically. The model was validated with representative measurements of AC loss in the coils, measured calorimetrically as well as magnetically using pick-up coils. The validation experiment confirms the predicted frequency dependence of the coupling loss, which is at low frequencies and at high frequencies, due to the skin effect. The transition between low- and high-frequency regimes occurs around a characteristic frequency that is directly related to the characteristic time constant associated with the current decay in (dis)charge experiments.
4 December 2023 in IEEE Transactions on Applied Superconductivity
We worked out an approach for obtaining “clean” magnets by introducing oxygen during the reaction heat treatment (RHT) of a single glass fiber insulated Nb 3 Sn Rutherford cable in a channel. A reduction of the RRR by 16% was measured while the glass fiber insulation and support structure was visually clean after the RHT. We developed a filled wax system, consisting of fully refined paraffin wax, carnauba wax and alumina particles, which is compatible with the common glass fiber insulation on Rutherford cables. The filled wax showed a flexural modulus of 19 GPa at −100 °C and a thermal shrinkage of −1.2% from RT to 77 K. We used a commercial glass ceramic coating on stainless steel as primary insulation in single cable in a channel applications or as secondary electrical insulation from the former. The coating survives the RHT and operation temperatures and keeps its electrical insulation properties.
25 December 2023 in IEEE Transactions on Applied Superconductivity
In the quest for climate neutrality in the aviation industry by 2050, technology development is one of the main pathways for Airbus. Owing to their high efficiency and current density, use of superconducting DC and AC distribution lines are a potential enabler for fully electric propulsion in a longer range aircraft, in particular in the scenario where liquid hydrogen provides a cold source on board of the aircraft. The ground-based Advanced Superconducting and Cryogenic Experimental power traiN Demonstrator (ASCEND) at Airbus intends to demonstrate the potential and feasibility of a cryogenic and superconducting powertrain as a breakthrough electric propulsion solution on future electric aircraft. A direct current distribution network is used in a generic propulsion system to transfer 500 kW power from the DC supply to an electrical converter, which transforms the energy into an alternating voltage/current to drive the superconducting motor. A relatively low voltage level of 300 V, and a current of 1700 A, is chosen to optimize the safety and installation in a future aircraft by operating at relatively low voltage. The DC link consists of a 10 m long two-pole superconducting Conductor on Round Core (CORC) cable, and demountable current leads, that transfer the power from the room temperature environment to the cryogenically cooled motor control unit. Downstream of this unit a 3-phase AC link operating at 500 Hz delivers power to a superconducting motor. Both the AC and DC links are cooled with a flow of subcooled LN 2 . The components of the DC and AC links have been designed, manufactured and recently integrated into the ASCEND test bench in Ottobrunn, Germany. We present the powering of the DC link up to nominal current, as well as commissioning and integration experience.