Duo Liu

Duo Liu

Auto-generated profile, based on publicly available information

Duo Liu

State Key Laboratory of Precision Welding & Joining of Materials and Structures, Harbin Institute of Technology, Harbin, China

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 July 2022 in Materials Science and Engineering: A
Verified
Journal Article
Closed access
JCJian Cao
Jian Cao
YSYanyu Song
Yanyu Song
HZHaitao Zhu
Haitao Zhu
XLXingyi Li
Xingyi Li
TWTao Wang
Tao Wang
DLDuo Liu
Duo Liu

4 March 2024 in Construction and Building Materials
Verified
Journal Article
Closed access
ZYZaixin Yang
Zaixin Yang
CMChengxiang Miao
Chengxiang Miao
WDWenqin Deng
Wenqin Deng
DLDuo Liu
Duo Liu
JZJiandong Zhang
Jiandong Zhang
JianCheng GuJianCheng Gu
JianCheng Gu

1 January 2019 in Science and Technology of Welding and Joining
Verified
Journal Article
Closed access
HLHongliang Li
Hongliang Li
DLDuo Liu
Duo Liu
QMQiang Ma
Qiang Ma
NGNing Guo
Ning Guo
Xiaoguo SongXiaoguo Song
Xiaoguo Song
JFJicai Feng
Jicai Feng
Dissimilar joint between 304L austenitic stainless steel and low-alloy steel 16Mn was underwater wet welded using self-shielded nickel-based tubular wire. Microstructure, mechanical properties and corrosion behaviour of dissimilar welded joints were discussed. Ni-based weld metal was fully austenitic with well-developed columnar sub-grains. Type II boundary existed between Ni-based weld metal and ferritic base metal in underwater welds similar to that in air welds. Major alloying elements distributed non-uniformly across the austenitic weld metal/16Mn interface. Maximum hardness values in wet welding appeared in a coarse-grained heat-affected zone at the 16Mn side, which possessed very low impact toughness. Underwater Ni-based welded joints fractured at Ni-based weld metal under tensile test. Ni-based weld metal had favourable corrosion resistance similar to 304L base metal.

14 May 2019 in Journal of the American Ceramic Society
Verified
Journal Article
Closed access
PDF file
YSYanyu Song
Yanyu Song
DLDuo Liu
Duo Liu
XSXiaoguo Song
Xiaoguo Song
SHShengpeng Hu
Shengpeng Hu
Jian CaoJian Cao
Jian Cao

1 September 2021 in Polish Maritime Research
Verified
Journal Article
Open access
PDF file
Hongliang LiHongliang Li
Hongliang Li
SLShixiong Liu
Shixiong Liu
QMQiang Ma
Qiang Ma
PWPengfei Wang
Pengfei Wang
DLDuo Liu
Duo Liu
QZQiang Zhu
Qiang Zhu
The paper described the experimental findings of underwater wet welding of E40 steel using self-shielded flux-cored wire with a TiO 2 -FeO-MnO slag system. The arc stability, weld quality and corrosion resistance with different heat inputs were studied. The results showed that the wet welding process of the designed wire displayed good operability in the range of investigated parameters. The microstructure and mechanical properties of the weld metal depended on the heat input. Due to the high fraction of acicular ferrite in the weld metal, the mechanical properties of the weld metal under low heat input had better tensile strength and impact toughness. Fracture morphologies at low heat input had uniform and small dimples, which exhibited a ductile characteristic. The diffusible hydrogen content in the deposited metal obtained at a heat input of 26 kJ/cm significantly reduced to 14.6 ml/100g due to the combined effects of Fe 2 O 3 addition and the slow solidification rate of molten metal. The microstructure also had a significant effect on the corrosion resistance of the weld metal. The weld metal with high proportions of acicular ferrite at low heat input exhibited the lowest corrosion rate, while the base metal possessed a reduced corrosion resistance. These results were helpful to promote the application of low alloy high strength steel in the marine fields.

28 January 2026 in Advanced Composites and Hybrid Materials
Verified
Journal Article
Open access
PDF file
HZHaitao Zhu
Haitao Zhu
BCBo Cheng
Bo Cheng
Yanyu SongYanyu Song
Yanyu Song
HKHyoung Seop Kim
Hyoung Seop Kim
NCNaibin Chen
Naibin Chen
Xiaoguo SongXiaoguo Song
Xiaoguo Song
Reliable brazing of C/C-SiC composites to stainless steel is hindered by severe residual stresses and uncontrolled interfacial reactions. Here, we introduce a CuMnCr/Mo/Cu multilayer interface that aims to simultaneously regulates stress distribution and interfacial chemistry. Cr from the CuMnCr layer preferentially reacts with C/C-SiC, forming a Cr7C3 + Cr3Si reaction layer, while Fe and Cr from stainless steel diffuse into Cu to produce a (Cu, Fe, Cr) solid solution. The Mo interlayer mainly acts as both a diffusion barrier and a compliant stress absorber, isolating reaction zones and concentrating part of the residual stress within itself. Finite-element simulations confirm that this design reduces peak Mises stress from 684 MPa to 444 MPa. At an optimized brazing temperature of 980 °C, the joint achieves a shear strength of 32.2 MPa, corresponding to 57.5% of the intrinsic strength of C/C-SiC. Thermodynamic, kinetic, and first-principles analyses suggest that Cr plays a dominant role in interfacial bonding, whereas Mo contributes to the redistribution of residual stress and mitigation of brittle fracture. Overall, this multilayer strategy provides mechanistic insight into how Cr-driven interfacial control can be combined with Mo-assisted stress management to design reliable C/C-SiC-metal joints, while the long-term service behavior and extension to other composite/steel combinations remain to be clarified in future work.