High syringly/guaiacyl (S/G) ratios are advantageous for chemical pulp production due to higher delignification rates, higher pulp yields and lower chemical consumption. Near infrared-based partial least-squares regression (PLS-R) models were developed to assess the S/G ratio of Eucalyptus globulus wood using analytical pyrolysis as the reference method. The PLS-R models obtained using the wavenumber range from 6100cm−1 to 5450cm−1 (1639–1835nm) of the preprocessed spectra using first derivative (1stDer) and first derivative in combination with; vector normalisation (1stDerVN), multiplicative scatter correction (1stDerMSC) and straight-line-subtraction (1stDerSLS), and the second derivative (2ndDer), are well qualified for rapid screening the S/G ratio of Eucalyptus globulus wood. Overall, models using 1stDerVN and 1stDerMSC preprocess (78 samples) requiring only three PLS components have the best statistics with coefficient of determination ( r2) = 0.97, root mean square error of cross-validation ( RMSECV)=0.025 and residual prediction deviation ( RPD) = 5.7
The reduction of resinous species in Portuguese forest areas has caused constraints to wood industry supplies. Portugal represents the extreme southwest of Scots pine (Pinus sylvestris) natural distribution and large gaps exist in the knowledge of its wood-quality characteristics. Understanding the relationship between these traits is important for recognizing which combination of wood properties is the most suitable for specific uses. To address these questions, we assessed wood-quality traits, namely, wood-density components (microdensitometric analysis), chemical composition (NIR spectrometry) and mechanical properties (bending tests) of wood samples collected at five representative forest sites in Portugal. Our results showed that Portuguese Pinus sylvestris has good radial growth and denser wood, higher extractive content and higher stiffness and strength than northern European provenances. The lignin content was within the range attributed to softwoods. Among the Portuguese stands, trees growing at lower-altitude sites exhibited denser wood and higher mechanical properties, while trees from high-elevations showed higher amounts of lignin. Ring density was more strongly correlated with earlywood than latewood density. A negative, non-significant correlation was found between ring density and width, supporting the assumption that the higher radial growth (ring width) does not negatively affect wood quality (density). In general, chemical properties had a weak relationship with physical and mechanical properties (MOE and MOR). Both mechanical traits were positively correlated with density and growth components, supporting the assumption that trees with high radial growth do not exhibit poorer mechanical performances.
1 January 2012 in Journal of Near Infrared Spectroscopy
Wood extractives, the non-cell wall components that can be removed by solvents, can play an important role in the protection of the living tree as well as derived wood products. On the other hand they can be detrimental for pulp and paper, paint and varnish films and adhesives. The objective of this work was to develop near infrared-based partial least squares regression models for the prediction of wood extractives. The developed models are well suited for screening of the ethanol and total extractives content of Eucalyptus globulus wood. The models for the prediction of ethanol extractives with residual prediction deviations above 5 are also suited for quality control. It is shown that samples with high extractives content always have a more intense OH combination band than the samples with low extractives content and that near infrared can be used for a rough estimation of the relative performance of the reference methods.
The valorisation of agro-industrial residues presents a challenge in obtaining economically sustainable and environmentally friendly industrial processes. Olive pomace is a by-product generated in large quantities, from olive oil extraction. This residue mostly consists of lignocellulosic materials. The aim of this study was to evaluate the potential use of extracted olive pomaces (EOP) obtained from olives with different ripening indexes (RI) and from different cultivars (Cobrançosa; RI = 2.5; 3.3 and 4.7; and Galega Vulgar; RI = 1.8; 2.9 and 4.8), to produce bioactive oligosaccharides from hemicelluloses by autohydrolysis. The hydrothermal treatment conditions were optimized by Response Surface Methodology, following a central composite rotatable design (CCRD), as a function of temperature (T: 142–198 °C) and time (t: 48–132 min), corresponding to severity factor (SF) values from 3.2 to 4.9. For all pomace samples, soluble sugar production was described by concave surfaces as a function of temperature and time. Autohydrolysis with SF equal or higher than 4.0 produced higher sugar yields, with maximum values around 180 g glucose equivalent/kg EOP for SF of 4.7 (190 °C/120 min) or 4.9 (198 °C/90 min). These values were similar for both cultivars and were not dependent on the ripening stage of the olives. Maximum oligosaccharide (OS) yields of 98% were obtained by autohydrolysis with SF of 4.0. The increase in SF to 4.9 resulted in a decrease in OS yield to 86–92%, due to the release of monomeric sugars. The monosaccharides were mostly xylose (55.8–67.7% in Galega; 50.4–69.0% in Cobrançosa liquid phases), and glucose, galactose, arabinose and rhamnose, in smaller quantities. Therefore, the production of bioactive xylo-oligosaccharides (XOS) from olive pomaces mainly depends on the hydrothermal conditions used.