Gurpreet Kaur

Gurpreet Kaur

Auto-generated profile, based on publicly available information

Gurpreet Kaur

High Power Laser Lab, Department of Physics, Indian Institute of Technology Roorkee, Roorkee, India

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2014 in Applied Surface Science
Verified
Journal Article
Closed access
NVN. Venugopal
N. Venugopal
GKGurpreet Kaur
Gurpreet Kaur
AMAnirban Mitra
Anirban Mitra

1 January 2015 in Advanced Materials Letters
Verified
Journal Article
Closed access
GKGurpreet Kaur
Gurpreet Kaur
AMAnirban Mitra
Anirban Mitra
KYK.L. Yadav
K.L. Yadav

1 September 2015 in Journal of Materials Science: Materials in Electronics
Verified
Journal Article
Closed access
PDF file
GKGurpreet Kaur
Gurpreet Kaur
AMAnirban Mitra
Anirban Mitra
KYK. L. Yadav
K. L. Yadav

6 August 2015 in IEEE Transactions on Nanotechnology
Verified
Journal Article
Closed access
GKGurpreet Kaur
Gurpreet Kaur
AMAnirban Mitra
Anirban Mitra
KYK. L. Yadav
K. L. Yadav
The influence of beam energy on the structural, optical, and electrical properties of Al-doped ZnO (Al:ZnO) thin films deposited using the pulsed laser deposition technique is observed systematically. X-ray diffraction analysis shows the crystalline nature of the thin films with preferred orientation (0 0 2) plane and hexagonal wurtzite structures. The impact of beam energy on the lattice strain is examined by Williamson-Hall (W-H) plots. The surface morphology examined by field emission scanning electron microscopy (FESEM) and atomic force microscopy analysis show the increased aspect ratio of grains, particle density, and surface coverage with the beam energy. The elemental composition of the films depends on the beam energy. Optical properties characterized by UV-visible spectroscopy indicate high transparency over 75% in the visible region and a sharp UV absorption. The optical band gap, $E_{g}$ obtained from Tauc's plot indicates a decrease in the energy gap with an increase in laser beam energy. Burstein-Moss (B-M) shift is observed in the band gap due to Al-doping. Photoluminescence (PL) properties of the thin films indicate visible emission peaks, corresponding to deep level defects. The electrical properties analyzed by Four probe technique depict that the thin films possess a resistivity ~10 -3 Ω·cm. Al:ZnO films show good optoelectronic properties for their practical applicability in devices such as solar cells and transparent display electrodes.

19 July 2024
Verified
Book Chapter
Closed access
PDF file
MRMamta Rani
Mamta Rani
GKGurpreet Kaur
Gurpreet Kaur
MSManmeet Singh
Manmeet Singh
DKDaljit Kaur
Daljit Kaur
Chips also known as integrated chips or microchips are the basic building blocks of all the device technologies (laptops, smartphones, cars, machines, scanners, industrial robots, etc.) that we are using today. A chip is generally made up of a thin slice of semiconductor silicon wafer on which billions of complex electronic circuits are integrated. The chips made in 1971 contain a few thousand transistors which are now increased to 10 billion on the size of a fingernail, for example, Apple’s M1 Ultra with 114 billion transistors. The demand for higher density and speed with low power consumption can only be met by integrating new materials and device architectures along with system technology co-optimization, this chapter will first discuss the history and development of semiconductor chip technology. Then a comprehensive review of the prospective 2D semiconducting materials and their performance of 2D-based electronic devices is discussed. Finally, the challenges and opportunities in chips based on 2D semiconducting materials have been put forth. <!----> <!----> <!----> <!---->