Charles L. Brown Department of Electrical and Computer Engineering, University of Virginia, Thornton Hall, 351 McCormick Road, Charlottesville, Virginia 22904, USA
Auto-generated profile, based on publicly available information
Harold A. Haldren
Charles L. Brown Department of Electrical and Computer Engineering, University of Virginia, Thornton Hall, 351 McCormick Road, Charlottesville, Virginia 22904, USA
As modern aerospace and automotive designs continually strive for higher performance, and thus rely on advanced composite structures where adhesive bonding is a preferred method of joining, the need for a robust quantitative nondestructive bond strength measurement method has increased. As such, advanced nondestructive evaluation methods have been researched for increased sensitivity to weak interfacial bonding and ultimately to detect “kissing” bonds. In this work, a phase-based method for interrogating bonded joints and detecting weak adhesion is developed by using swept-frequency phase measurements of ultrasonic waves reflected from an adhesive joint and modeling adhesive interfaces as a distributed spring system. The method's sensitivity to bond strength is explored by ultrasonic phase evaluation of tri-layer joints with bond quality varied by controlling ultraviolet light exposure and extracting interfacial stiffness constants of the bonds. Mechanical tensile tests found each joint failed adhesively, allowing a linear correlation to be drawn between interfacial stiffness and tensile strength, consistent with previous theoretical research. The ultrasonic phase measurement method identifies intermediate bond strengths, rather than simply detecting good or bad bonds. This technique has the potential for the verification of bond quality in lightweight aerospace and automotive designs utilizing advanced composite structures with adhesive attachments.
A digitally controlled instrument for conducting single-frequency and swept-frequency ultrasonic phase measurements has been developed based on a constant-frequency pulsed phase-locked-loop (CFPPLL) design. This instrument uses a pair of direct digital synthesizers to generate an ultrasonically transceived tone-burst and an internal reference wave for phase comparison. Real-time, constant-frequency phase tracking in an interrogated specimen is possible with a resolution of 0.000 38 rad (0.022°), and swept-frequency phase measurements can be obtained. Using phase measurements, an absolute thickness in borosilicate glass is presented to show the instrument’s efficacy, and these results are compared to conventional ultrasonic pulse-echo time-of-flight (ToF) measurements. The newly developed instrument predicted the thickness with a mean error of −0.04 μm and a standard deviation of error of 1.35 μm. Additionally, the CFPPLL instrument shows a lower measured phase error in the absence of changing temperature and couplant thickness than high-resolution cross-correlation ToF measurements at a similar signal-to-noise ratio. By showing higher accuracy and precision than conventional pulse-echo ToF measurements and lower phase errors than cross-correlation ToF measurements, the new digitally controlled CFPPLL instrument provides high-resolution absolute ultrasonic velocity or path-length measurements in solids or liquids, as well as tracking of material property changes with high sensitivity. The ability to obtain absolute phase measurements allows for many new applications than possible with previous ultrasonic pulsed phase-locked loop instruments. In addition to improved resolution, swept-frequency phase measurements add useful capability in measuring properties of layered structures, such as bonded joints, or materials which exhibit non-linear frequency-dependent behavior, such as dispersive media.
As adhesive bonding is a preferred method of joining advanced composite structures for modern aerospace and automotive designs, the need for a quantitative nondestructive evaluation (NDE) method for adhesive bond strength has sharply increased. For many years, adhesively bonded joints have been examined with conventional NDE methods, but none have proved able to detect weak or “kissing” bonds, except where major bonding defects occur. Here, the problem of weak interfacial bonding is investigated with a novel swept-frequency ultrasonic phase measurement method. High- resolution, swept-frequency ultrasonic phase measurements are obtained at each frequency through the use of a constant- frequency pulsed phase-lock-loop instrument. The method is tested on single lap joints fabricated with polished glass adherents and adhesive cured with ultraviolet (UV) light. The cohesive and adhesive bonding properties are modified by varying the adhesive’s exposure time to UV light and thereby changing the degree-of-cure. After fitting the measured phase response to a model of the ultrasonic response of the bonded joint, the stiffness constant of the adhesive/adherent interface is found. The interfacial stiffness constant is shown to have a strong linear correlation with measured mechanical tensile strength. As such, high-resolution swept-frequency phase measurements are shown to have a sensitivity to interfacial bond strength without the presence of gross bonding defects, allowing for bond strength quantification rather than a simple identification of “good” or “bad” bonding. This method has the potential to be a quality control and service life assessment method for both newly-fabricated and in-service bonded joints for the aerospace, automotive, and other industries.