11 January 2021 in Solid Earth
Computer X-ray microtomography (µXCT) represents a powerful tool for investigating the physical properties of porous rocks. While calculated porosities determined by this method typically match experimental measurements, computed permeabilities are often overestimated by more than 1 order of magnitude. This effect increases towards smaller pore sizes, as shown in this study, in which nanostructural features related to clay minerals reduce the permeability of tight reservoir sandstone samples. Focussed ion beam scanning electron microscopy (FIB-SEM) tomography was applied to determine the permeability effects of illites at the nanometre scale, and Navier–Stokes equations were applied to calculate the permeability of these domains. With these data, microporous domains (porous voxels) were defined using microtomography images of a tight reservoir sample. The distribution of these domains could be extrapolated by calibration against size distributions measured in FIB-SEM images. For this, we assumed a mean permeability for the dominant clay mineral (illite) in the rock and assigned it to the microporous domains within the structure. The results prove the applicability of our novel approach by combining FIB-SEM with X-ray tomographic rock core scans to achieve a good correspondence between measured and simulated permeabilities. This methodology results in a more accurate representation of reservoir rock permeability in comparison to that estimated purely based on µXCT images.
17 June 2019 in Geofluids
Subsurface temperature data is usually only accessible as point information with a very limited number of observations. To spatialize these isolated insights underground, we usually rely on interpolation methods. Unfortunately, these conventional tools are in many cases not suitable to be applied to areas with high local variability, like densely populated areas, and in addition are very vulnerable to uneven distributions of wells. Since thermal conditions of the surface and shallow subsurface are coupled, we can utilize this relationship to estimate shallow groundwater temperatures from satellite-derived land surface temperatures. Here, we propose an estimation approach that provides spatial groundwater temperature data and can be applied to natural, urban, and mixed environments. To achieve this, we combine land surface temperatures with anthropogenic and natural processes, such as downward heat transfer from buildings, insulation through snow coverage, and latent heat flux in the form of evapotranspiration. This is demonstrated for the city of Paris, where measurements from as early as 1977 reveal the existence of a substantial subsurface urban heat island (SUHI) with a maximum groundwater temperature anomaly of around 7 K. It is demonstrated that groundwater temperatures in Paris can be well predicted with a root mean squared error of below 1 K by means of satellite-derived land surface images. This combined approach is shown to improve existing estimation procedures that are focused either on rural or on urban conditions. While they do not detect local hotspots caused by small-scaled heat sources located underground (e.g., sewage systems and tunnels), the findings for the city of Paris for the estimation of large-scale thermal anomalies in the subsurface are promising. Thus, the new estimation procedure may also be suitable for other cities to obtain a more reliable insight into the spatial distribution of urban ground and groundwater temperatures.
11 December 2020 in Solid Earth
Hydraulic fracture apertures predominantly control fluid transport in fractured rock masses. Hence, the objective of the current study is to investigate and compare three different laboratory-scale methods to determine hydraulic apertures in fractured (Fontainebleau and Flechtinger) sandstone samples with negligible matrix permeability. Direct measurements were performed by using a flow-through apparatus and a transient-airflow permeameter. In addition, a microscope camera permitted measuring the mechanical fracture apertures from which the corresponding hydraulic apertures were indirectly derived by applying various empirical correlations. Single fractures in the sample cores were generated artificially either by axial splitting or by a saw cut resulting in hydraulic apertures that ranged between 8 and 66 µm. Hydraulic apertures, accurately determined by the flow-through apparatus, are used to compare results obtained by the other methods. The transient-airflow permeameter delivers accurate values, particularly when repeated measurements along the full fracture width are performed. In this case, the derived mean hydraulic fracture apertures are in excellent quantitative agreement. When hydraulic apertures are calculated indirectly from optically determined mechanical apertures using empirical equations, they show larger variations that are difficult to compare with the flow-through-derived results. Variations in hydraulic apertures as observed between methods are almost certainly related to differences in sampled fracture volume. Overall, using direct flow-through measurements as a reference, this study demonstrates the applicability of portable methods to determine hydraulic fracture apertures at both the laboratory and outcrop scales.
13 July 2021 in Solid Earth
Construction of cavities in the subsurface is always accompanied by excavation damage. Especially in the context of deep geological nuclear waste disposal, the evolving excavation damaged zone (EDZ) in the near field of emplacement tunnels is of utmost importance concerning safety aspects. As the EDZ differs from the intact host rock due to enhanced hydraulic transmissivity and altered geomechanical behavior, reasonable and location-dependent input data on hydraulic and mechanical properties are crucial. Thus, in this study, a hydromechanical characterization of an EDZ in the Mont Terri underground rock laboratory, Switzerland, was performed using three different handheld devices: (1) air permeameter, (2) microscopic camera and (3) needle penetrometer. The discrete fracture network (DFN), consisting of artificially induced unloading joints and reactivated natural discontinuities, was investigated by a portable air permeameter and combined microscopic imaging with automatic evaluation. Geomechanical and geophysical characterization of the claystone was conducted based on needle penetrometer testing at the exposed rock surface. Within the EDZ, permeable fractures with a mean hydraulic aperture of 84 ± 23 µm are present. Under open conditions, self-sealing of fractures is suppressed, and cyclic long-term fracture aperture oscillations in combination with closure resulting from convergence processes is observed. Based on measured needle penetration indices, a uniaxial compressive strength of 30 ± 13 MPa (normal to bedding) and 18 ± 8 MPa (parallel to bedding) was determined. Enhanced strength and stiffness are directly related to near-surface desaturation of the claystone and a sharp decrease in water content from 6.6 wt % to 3.7 wt %. The presented methodological approach is particularly suitable for time-dependent monitoring of EDZs since measurements are nondestructive and do not change the actual state of the rock mass. This allows for a spatially resolved investigation of hydraulic and mechanical fracture apertures, fracture surface roughness, and physico-mechanical rock parameters and their intra-facies variability.
20 September 2019 in Rock Mechanics and Rock Engineering
19 May 2022 in Environmental Earth Sciences
Calcite is a highly abundant mineral in the Earth’s crust and occurs as a cement phase in numerous siliciclastic sediments, where it often represents the most reactive component when a fluid percolates through the rock. Hence, the objective of this study is to derive calcite dissolution rates on different scales in a reservoir sandstone using mineral surface experiments combined with vertical scanning interferometry (VSI) and two types of core plug experiments. The 3D geometry of the calcite cement phase inside the rock cores was characterized by X-ray micro-computed tomography (µXCT) and was used to attempt dissolution rate upscaling from the mineral surface to the core scale. Initially (without upscaling), our comparison of the far-from-equilibrium dissolution rates at the mineral surface (µm-mm-scale, low fluid residence time) and the surface normalized dissolution rates obtained from the core experiments (cm-scale, high fluid residence time) revealed differences of 0.5–2 orders of magnitude. The µXCT geometric surface area connected to the open pore space $$\left( {GSA_{{Cc,{\text{open}}}} } \right)$$ considers the fluid accessibility of the heterogeneously distributed calcite cement that can largely vary between individual samples, but greatly affects the effective dissolution rates. Using this parameter to upscale the rates from the µm- to the cm-scale, the deviation of the upscaled total dissolution rates from the measured total dissolution rates was less than one order of magnitude for all investigated rock cores. Thus, $$GSA_{{Cc,{\text{open}}}}$$ showed to be reasonably suitable for upscaling the mineral surface rates to the core scale.