18 March 2015 in Geophysics
Carbonate rocks have a complex pore structure, show strong heterogeneity, and have a wide range of velocities that lead to more complicated velocity-porosity relationships compared with sandstones. We designed and prepared 72 carbonate synthetic cores with known pore structures according to the control variate principle. We measured the P- and S-wave velocities of these cores by an ultrasonic pulse transmission method, analyzed the effects of the pore aspect ratio (AR) and pore size on velocities, and compared the experimental results with predictions of effective medium theories (EMTs). The matrix of our synthetic cores was consolidated mixture of carbonate cuttings and epoxy. We randomly imbedded predesigned penny-shaped silicone disks or expandable polystyrene balls into the matrix during the core preparation process to simulate secondary pores. The experimental results indicated that Han’s empirical linear velocity-porosity relation was a good prediction for cores with only interparticle pores. Secondary pores played an important role in the velocity variation of carbonates. Cores with a larger AR had faster velocities. Different ARs could lead to velocity variations as high as at a given porosity. When the wavelengths were larger than the pore size, cores with larger secondary pores found higher velocities under the same pore shape, pore fluid, and porosity condition. Different pore sizes could contribute to nearly 15% velocity variation at a given porosity. The comparison between our measurements and EMT predictions indicated that for carbonate rocks with a complicated pore structure, the self-consistent model gave more reliable predictions when the secondary pore size was relatively small () and Kuster and Toksoz formulations as well as the differential effective medium model gave more satisfactory results when the secondary pore size was relatively large (, or even smaller).
1 March 2018 in Geophysics
The existing methods of well-logging interpretation cannot be applied accurately to the exploration and evaluation of carbonate reservoirs because of the fracture development. Based on the fracture density obtained by core analysis in a carbonate reservoir located in the Ordos basin, the west of China, three types of fracture density (low, medium and high fracture density) of the target formation were identified. We investigated the effect of fractures on acoustic logging signals in time and frequency domain by Hilbert-Huang transform (HHT) and extracted 11 features in time domain and 9 features in frequency domain. Then, we reduced the features in time and frequency domain to three principal components by principal component analysis (PCA). Finally, a new prediction model of GA-SVM method based on Hilbert-Huang transform of acoustic logging data was reported to predict the fracture density. The results show that fracture density has a greater effect on the attenuation of IMF2 and IMF3 components for three different types of formation by empirical mode decomposition (EMD) analysis. The energies of Stoneley wave and shear wave have higher sensitivity than compressional wave. Compared with time domain, the distribution in high frequency domain has a greater correlation with fracture density by Hilbert spectrum and marginal spectrum. The correlation coefficients between fracture density and 9 features in frequency domain (R2=0.5~0.7) are better than the coefficients with 11 features in time domain (R2=0.3~0.5). Core analysis and interpretation of resistivity image logging support the validity and effectiveness of our model. The prediction accuracy using the features in frequency domain can reach to 82~90%, which is much higher than using the features in time domain with accuracy of 52~59%. The application with more information of acoustic logging data in our model can avoid the error in velocity picking, which points out the direction for the future prediction.
22 May 2019 in Geophysical Research Letters
This study analyzes earthquake recordings from four near‐source (<10 km) stations near Fox Creek, Alberta, a region known for hydraulic fracturing‐induced seismicity. We examine the spatiotemporal variations of focal mechanisms and seismic anisotropy in the sedimentary strata. The focal mechanisms of surrounding earthquake swarms are generally consistent with the strike‐slip mechanism of the ML4.6 earthquake, favoring a flower type of fault structure. The NE‐SW‐orientated fast splitting direction, determined from the shear wave splitting measurements, reflects the combined effects of (1) N‐S faults and (2) NE‐SW time‐dependent hydraulically stimulated fractures. The latter effect dominates the apparent anisotropy during the days leading to the mainshock, while its contributions are reduced by 60–70% after the mainshock. Loss of fluid into the fault damage zone, which causes the closure of fractures, is responsible for the observed spatiotemporal variation of seismic anisotropy near the hydraulic fracturing well.
10 June 2016 in Geophysics
Fractures greatly increase the difficulty of oil and gas exploration and development in reservoirs consisting of interlayered carbonates and shales and increase the uncertainty of highly efficient development. The presence of fractures or layered media is also widely known to affect the elastic properties of rocks. The combined effects of fractures and layered media are still unknown. We have investigated the effects of fracture structure on wave propagation in interlayered carbonate and shale rocks using physical models based on wave theory and the similarity principle. We have designed and built two sets of layered physical models with randomly embedded predesigned vertically aligned fractures according to the control variate principle. We have measured the P- and S-wave velocities and attenuation and analyzed the effects of fracture porosity and aspect ratio (AR) on velocity, attenuation, and power spectral dimension of the P- and S-waves. The experimental results indicated that under conditions of low porosity (), Han’s empirical velocity-porosity relations and Wang’s attenuation-porosity relation combined with Wyllie’s time-average model are a good prediction for layered physical models with randomly embedded fractures. When the porosity is constant, the effect of different ARs on elastic wave properties can be described by a power law function. We have calculated the power spectrum fractal dimension of the transmitted signal in the frequency domain, which can supplement the S-wave splitting method for estimating the degree of anisotropy. The simple power law relation between the power spectrum fractal dimension of the P-waveform and fracture density suggests the possible use of P-waves for discriminating fracture density. The high precision and low error of this processing method give new ideas for rock anisotropy evaluation and fracture density prediction when only P-wave data are available.
13 October 2013 in Petroleum Science
28 May 2011 in Petroleum Science
The shear strength of gas-hydrate-bearing reservoirs is one of the most important parameters used to study mechanical properties of gas-hydrate-bearing reservoirs. The shear strength of gas-hydratebearing reservoirs changes with filling and cementation of gas hydrates, which will affect the wellbore and reservoir stability. Traditional shear tests could not be conducted on gas-hydrate-bearing core samples because the gas hydrates exist under a limited range of temperature and pressure conditions. This paper describes a novel shear apparatus for studying shear strength of gas-hydrate-bearing core samples under original reservoir conditions. The preparation of gas-hydrate-bearing core samples and subsequent shear tests are done in the same cell. Cohesion and internal friction angle of the core samples with different saturations of gas hydrates were measured with the apparatus. The effect of gas hydrates on the shear strength of reservoirs was quantitatively analyzed. This provides a foundation for studying wellbore and reservoir stability of gas-hydrate-bearing reservoirs.