Rajkumar Vijayakumar

Rajkumar Vijayakumar

Auto-generated profile, based on publicly available information

Rajkumar Vijayakumar

Department of Mechanical Engineering, Sri Ramakrishna Institute of Technology, Coimbatore, India

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2014 in Procedia Engineering
Verified
Journal Article
Open access
PSP. Sadeesh
P. Sadeesh
MKM. Venkatesh Kannan
M. Venkatesh Kannan
VRV. Rajkumar
V. Rajkumar
PAP. Avinash
P. Avinash
NAN. Arivazhagan
N. Arivazhagan
SNS. Narayanan
S. Narayanan
The joining of dissimilar AA2024 and AA6061 aluminium plates of 5mm thickness was carried out by friction stir welding (FSW) technique. Optimum process parameters were obtained for joints using statistical approach. Five different tool designs have been employed to analyse the influence of rotation speed and traverse speed over the microstructural and tensile properties. In FSW technique, the process of welding of the base material, well below it's melting temperature, has opened up new trends in producing efficient dissimilar joints. Effect of welding speed on microstructures, hardness distribution and tensile properties of the welded joints were investigated. By varying the process parameters, defect free and high efficiency welded joints were produced. The ratio between tool shoulder diameter and pin diameter is the most dominant factor. From microstructural analysis it is evident that the material placed on the advancing side dominates the nugget region. The hardness in the HAZ of 6061 was found to be minimum, where the welded joints failed during the tensile studies

1 January 2014 in Procedia Engineering
Verified
Journal Article
Open access
VRV. RajKumar
V. RajKumar
MVM. VenkateshKannan
M. VenkateshKannan
PSP. Sadeesh
P. Sadeesh
NAN. Arivazhagan
N. Arivazhagan
KRK. Devendranath Ramkumar
K. Devendranath Ramkumar
This research paper deals with the characterization of friction stir welded dissimilar Aluminium alloys AA 5052 and AA6061. The coupons of above metals were friction - stir welded using cylindrical pin tool using at constant speed of 710rpm and at two different feed rates of 28 and 20mm/min. Macrographs showed proper mixing due to effective stirring of cylindrical tool pin while keeping the lower feed rate. Further, extensive micro structural examination showed variation of grain size in each zone and their influence on mechanical properties. Tensile test and hardness measurements were done as a part of mechanical characterization. Correlating mechanical and metallurgical properties it is deduced that the sample welded at lower feed rate performed better in terms of ductility

1 November 2014 in Materials & Design (1980-2015)
Verified
Journal Article
Closed access
VRV. Rajkumar
V. Rajkumar
NAN. Arivazhagan
N. Arivazhagan

1 January 2014 in Procedia Engineering
Verified
Journal Article
Open access
VRV. Rajkumar
V. Rajkumar
NAN. Arivazhagan
N. Arivazhagan
KRK. Devendranath Ramkumar
K. Devendranath Ramkumar
This work involves with investigations on Maraging steel weldments done by GTA welding technique. Similar welding of maraging steel plates of 5mm thick using ErNiCrMo-3 filler wire was done in order to evaluate the weldability and performance characteristics. Micro structural and X- Ray diffraction analysis were done to analyze the structure and phases developed post – weld. Block martensite was formed in the heat affected zones of the parent metal. Tension testing using different strain rates and hardness profile measurements were done to investigate the mechanical properties and the study concludes that the strain rate has considerable influence on the nature of ductility whereas it has very less influence on the Ultimate Strength of Maraging steel

1 January 2014 in Procedia Engineering
Verified
Journal Article
Open access
MVM. Venkateshkannan
M. Venkateshkannan
VRV. Rajkumar
V. Rajkumar
PSP. Sadeesh
P. Sadeesh
NAN. Arivazhagan
N. Arivazhagan
SNS. Narayanan
S. Narayanan
KRK. Devendranath Ramkumar
K. Devendranath Ramkumar

21 December 2017
Verified
Book Chapter
Open access
PDF file
RVRajkumar Vijayakumar
Rajkumar Vijayakumar
VKVenkatesh Kannan
Venkatesh Kannan
ANArivazhagan Natarajan
Arivazhagan Natarajan
This chapter investigates on the characterization of friction stir welded dissimilar aluminium alloys AA2024 with AA5052, AA2024 with AA6061 and AA 5052 with AA6061. Five tool designs were employed with first two dissimilar combinations to analyze the influence of rotation and traverse speed over microstructural and mechanical properties. H13 tool steel was used as tool material with various pin profiles which includes cylindrical, cylindrical-threaded, squared, tapered and stepped types. In the dissimilar welding of AA 2024 with AA 5052, sound welds were produced with stepped pin tool. In the dissimilar welding of AA 2024 with AA 6061, ratio between tool shoulder to diameter of tool pin was the most influential factor. Welded joints failed in the Heat affected zone (HAZ) of 6061 where the hardness values were comparatively less. In dissimilar welding of AA 5052 with AA6061, cylindrical pin tool was used at a constant speed of 710 rpm and at different feed rates of 28 and 40 mm/min. Micro structural examination showed variation of grain size in every zone and their influence on mechanical properties. Correlating mechanical and metallurgical properties, the optimized process parameters of speed and feed were identified to be 710 rpm and 28 mm/min respectively for all attempted dissimilar combinations.