25 May 2017 in Journal of Composite Materials
The effects of carbon fiber amount and length were studied on the flame retardant, thermal, and mechanical properties of the intumescent polypropylene composites. The flame retardant properties of the intumescent polypropylene-based composites were investigated using limiting oxygen index, vertical burning test (UL-94), and mass loss calorimeter. The mechanical properties of the composites were studied using tensile test and dynamic mechanical analysis. According to the flammability tests results, the antagonistic interaction was observed between carbon fiber and ammonium polyphosphate. The limiting oxygen index value reduced steadily as the added amount of carbon fiber increased. Mechanical test results revealed that the addition of carbon fiber increased the tensile strength and the elastic modulus as the added amount increased. No effect of carbon fiber length was observed on the flammability, fire performance, and tensile properties of composites, whereas the elastic modulus increased as the carbon fiber initial length increased.
21 October 2022 in Journal of Composite Materials
This study investigated the mechanical properties of polypropylene composites reinforced with short natural fibers obtained from plane tree ( Platanus orientalis L.) fruits. The fibers were harvested from the fruits that naturally fell from the tree in their standard length of about 6 mm. Composites were produced via melt blending using varied concentrations of the fibers (5–10–20–30 wt.%) and maleic anhydride grafted polypropylene (MAPP) copolymer as the coupling agent. The mechanical properties of the composites were characterized by tensile test, flexural test, dynamic mechanic analysis and ball-on-disc sliding wear test. The findings revealed that the fibers had a significant effect on the mechanical properties of the polypropylene matrix and the properties were found to improve linearly with increasing fiber concentration. At a 30 wt.% fiber concentration, the tensile and flexural strengths increased about 28% and 36% compared to pure polypropylene, respectively. At this fiber concentration, the modulus doubled compared to the pristine polymer. This increase is higher than that reported for most other natural fibers. Good miscibility between fibers and matrix, enhanced thermal stability, and about 30% reduction in friction coefficients were found. As a result, PTFs have the potential to be used in industries such as automotive, construction and sports which require mechanical strength and low weight.
28 June 2022 in International Journal of Innovative Engineering Applications
Bu çalışmada, polipropilen (PP)/poliamid 6 (PA6) karışımlarında kullanılan kemik külü ve uyumlaştırıcı olarak maleik anhidrit aşılı polipropilen (MAPP) katkısının kompozitlerin mekanik ve ayrıca tribolojik özellikleri üzerindeki etkileri araştırılmıştır. Kemik tozu özellikle gıda sektöründe atık bir malzeme olarak karşımıza çıkmaktadır. Polimer matrisli kompozitlerde değerlendirilmesi petrol bazlı içeriğin azaltılması ve biyo-bozunur malzeme avantajı sunmasından dolayı önem arz etmektedir. Kompozitler ergiyik harmanlama yöntemi ile bir çift vidalı ekstrüder kullanılarak üretilmiş ve ardından enjeksiyon kalıplama ile mekanik ve tribolojik testlerde kullanılacak numune ölçülerine kalıplanmışlardır. Kompozitlere çekme testi, üç-nokta eğme testi, Shore D sertlik testi ve ball-on-disk kayma aşınma testleri uygulanmış ve sonuçlar kompozit bileşimine göre karşılaştırılmıştır. Sonuçlar incelendiğinde, kemik külü katkısının sertlik üzerinde, uyumlaştırıcı katkısının ise çekme ve eğme mukavemeti üzerinde daha etkili olduğu bulunmuştur. %20 ve %30 kemik külü katkısında en yüksek mekanik özelliklere ulaşılmıştır. Kemik külünün sürtünme katsayılarını düşürmede de çok etkili olduğu, özellikle uyumlaştırıcı ile birlikte kullanıldığında aşınma direncini önemli miktarda (%98’e kadar) azalttığı bulunmuştur. Özetle, kemik külü ve MAPP sinerjik etkisi ile elde edilen PP/PA6 matrisli kompozitler mekanik ve aşınma direnci gerektiren uygulamalar için ümit vadetmektedir.
5 October 2023 in Journal of Reinforced Plastics and Composites
The main motivation of this work is to use ceramic microspheres (CMs) as a potential filler in polyamide 6 (PA6) to enhance its mechanical and tribological performances. Polyamide 6 composites bearing CMs in different weight ratios (10%–40%) are processed by melt blending and characterized primarily by tensile and bending test, dynamical mechanical analysis, and ball-on-disc wear test. This work clearly shows that the addition of CMs gives rise to superior mechanical and wear resistance contribution to PA6. The tensile strength, tensile modulus, flexural strength, and flexural modulus of the composites are enhanced up to 11%, 25%, 37%, and 80%, respectively, over those of the pristine polymer. The wear resistance of 40 wt% CMs containing composite is 60% higher than that of pure PA6. Consequently, it has been found that CMs can be a suitable alternative especially in applications where mechanical strength is desired due to its advantages of high rigidity and sliding wear resistance.
1 January 2021 in JOURNAL OF CHARACTERIZATION
Bu çalışmada, ağırlıkça farklı yüzdelerde (%5-10-20-30) cam fiber içeren polimetilmetakrilat (PMMA) matrisli kompozitlerin mekanik ve aşınma direnci özellikleri araştırılmıştır. Üretimde çift vidalı bir ekstrüder kullanılarak ergiyik harmanlama yöntemi tercih edilmiş olup, test numunelerinin üretiminde ise enjeksiyon kalıplamadan faydalanılmıştır. Kompozitlerin mekanik özellikleri 3-nokta eğme ve Shore D sertlik ölçümleri ile, aşınma özellikleri ise özel üretim bir ball-on-disk kuru kayma aşınma test cihazı kullanılarak incelenmiştir. Benzer şartlarda şekillendirilen saf PMMA da aynı testlerde kontrol numunesi olarak kullanılmış ve cam fiber konsantrasyonuna bağlı olarak bahsedilen testlerin sonuçları yorumlanmıştır. En yüksek eğme gerilmesi ve elastiklik modülü değerlerine (sırasıyla 121 MPa ve 7354 MPa) %30 cam fiber içeren PM30 numunesi ile ulaşılmıştır. Benzer şekilde, yüksek sertlik, düşük sürtünme ve düşük aşınma oranı gibi özellikler %20 ve %30 cam fiber içeren kompozitlerde gözlenmiştir. Bu durum, cam fiber içeriğindeki artışın kompozit rijitliğini arttırması ayrıca yorulma aşınması direncinin de iyileştirmesi ile ilişkilendirilmiştir.