15 September 2004 in Chemical Physics
27 February 2024 in IEEE Transactions on Electromagnetic Compatibility
This article aims to design transient voltage suppressor (TVS) diode array protection circuits under high-power microwave (HPM) pulse injection to protect sensitive semiconductor and microwave devices from interfered or even damaged by intentionally electromagnetic interference. First of all, conductivity modulation with charge dependent resistors is added into original nonlinear large signal TVS diode model provided by Infineon and simulated results by improved model are compared with measured results obtained by transmission line pulse measurement. Next, due to the fact that the capacitance of the TVS diode degrades RF performances of the protected device, a transmission line (TL) connecting with the TVS diode is designed to improve the S-parameters. Subsequently, design procedures of circuits with multiple discharge paths of TVS diodes are summarized. Based on above these two points, four protection circuits are proposed and tested under HPM measurement system. The highest overshoot protection ratio of these circuits is approximately 16.5–22 dB when the input HPM pulse power ranges from 50 to 63 dBm. Through simulated and measured results, couple microstrip TLs and effect of TL inductance on overshoot PRs are investigated.
27 November 2024 in IEEE Transactions on Electromagnetic Compatibility
This article examines the electrical-thermal-stress effects of a high-power handling limiter operating at DC-6 GHz, utilizing gallium arsenide positive-intrinsic-negative (PIN) technology for protection against intentional electromagnetic interference. The limiter's performance is evaluated under high-power microwave induced pulse injection at 2 GHz, with varying pulse widths and a pulse repetition frequency (PRF) of 50 Hz. Destruction of the limiter is observed when the pulse width and input power reach 3 μ s and 63 dBm, respectively. The failure mechanisms are analyzed in three aspects. First, the thermal distribution of the limiter's microstrip lines is understood through equivalent circuit analysis of the PIN diodes. The characteristics of the limiter across different frequencies are also investigated, with a focus on the power levels of PIN diodes near the limiter's input. Additionally, owing to the observed differences in heat-induced discoloration on the two PIN diodes near the input port, their thermal and stress effects are compared by incorporating temperature boundary conditions and absorbed power in the analysis. Thermal accumulation in the PIN diodes is further explored under a higher PRF of 100 kHz. Finally, the thermal and stress effects on the bonding wire interconnects near the limiter's input are considered. Postmeasurement observations reveal damage to both the bonding wire and the PIN diodes, indicating that the bonding wire fails after the PIN diodes.
22 December 2025 in IEEE Transactions on Electron Devices
This article aims to discuss the electrical–thermal-stress effect of three type gallium nitride (GaN) high-electron mobility transistors (HEMTs) under high-power microwave (HPM)-induced pulse injection, where sensitive semiconductor devices are susceptible to be disturbed or even destroyed by intentional electromagnetic interference (IEMI). CG2H40010F, CGH40010F, and CGH35015F, produced by Wolfspeed with identical matching circuits, are measured under HPM-induced pulse injection at 3 GHz with the pulsewidth of 100 ns and a pulse repetition frequency (PRF) of 1kHz. At the threshold powers of 51, 52, and 56 dBm for CG2H40010F, CGH40010F, and CGH35015F, respectively, the peak temperature of three HEMTs is at the same level. Subsequently, the thermal-stress analysis for three HEMTs is investigated with different temperature distributions and various vulnerable regions. Moreover, the thermal accumulation effect is considered with an augment PRF to 5 MHz. Furthermore, electrical breakdown, especially at the rising edge is studied under single and multiple pulse injection. Eventually, crack areas across three GaN HEMTs are examined through experimental characterizations.
10 February 2026 in IEEE Microwave and Wireless Technology Letters
In this letter, a compact and broadband ground coplanar waveguide (GCPW) to folded substrate-integrated waveguide (FSIW) transition is proposed by using a metallic blind via and a modified tapered strip line (TSL) in the middle layer. The modified TSL incorporates five U-shaped groove structures of different sizes and a pair of interdigital structures on a conventional tapered quarter-wavelength transformer. The subwavelength U-shaped groove structures provide a significant slow wave effect, reducing the longitudinal size of the quarter-wavelength transformer while enhancing the operating bandwidth. To verify the results, back-to-back transitions are fabricated and measured. The measurement results show that the proposed structure operates at 7.8–22.0GHz with reflection coefficient more than −10 and −10-dB fractional bandwidth (FBW) of 95%. Compared to the GCPW-to-FSIW transition using the traditional quarter-wavelength transformer, the proposed transition can increase the bandwidth and reduce the physical length of the quarter-wavelength transformer from 4.3 to 2.2mm, achieving a 49% miniaturization of the longitudinal length.
1 September 2026 in IEEE Transactions on Microwave Theory and Techniques