Shilin Zhang

Shilin Zhang

Auto-generated profile, based on publicly available information

Shilin Zhang

School of Materials Science and Engineering State Center for International Cooperation on Designer Low‐carbon and Environmental Materials (CDLCEM) Zhengzhou University Zhengzhou China

Research Focus & Metrics

Academic Career Length

1Year (2026-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 February 2026 in Energy & Environmental Materials
Verified
Journal Article
Open access
HXHongjie Xu
Hongjie Xu
CZChenggong Zheng
Chenggong Zheng
XZXiaofeng Zhu
Xiaofeng Zhu
YLYalu Li
Yalu Li
ZYZhongzheng Yang
Zhongzheng Yang
GSGuosheng Shao
Guosheng Shao
Lithium–sulfur (Li–S) batteries suffer from the infamous lithium polysulfides (LPSs) shuttle effect, which generates reduced utilization of active materials and polysulfide‐corrosion‐accelerated lithium dendrite, ultimately resulting in poor capacity and cycling stability. While various natural clays have demonstrated effective adsorption for LPSs, there is no consensus on the adsorption mechanisms and active sites. Inspired by the distinct acid–base chemistry of clay basal and edge surfaces, we designed a capsule‐shaped silicate clay (H‐ATP‐N 2 ) that is rich in protonated edge hydroxyl groups (‐OH 2+ ). The synthesis involved a two‐step process: first, microwave‐assisted acid treatment was used to efficiently activate the surface of fibrous attapulgite. Next, N 2 plasma etching was applied to further enrich the material with the ‐OH 2 + . These specific methods were chosen to optimize the activation and functionalization of attapulgite, enhancing its ability to serve as a highly effective polysulfide‐trapping interface for improved electrochemical energy storage. Compared with the surface hydroxyl sites, the ‐OH 2 + act as Lewis acid sites to accept lone electron pairs from LPSs, thereby exhibiting a stronger interaction to successfully inhibit the shuttle effect. With the protonated edge hydroxyl groups in attapulgite dominating LPSs adsorption via a Lewis acid–base adsorption mechanism, the H‐ATP‐N 2 cathodes deliver a 1139.9 mAh g −1 capacity at 0.1 C, and a reversible capacity of 808.6 mAh g −1 after 500 cycles at 0.5 C with an ultralow capacity decay rate of 0.04% per cycle, which have surpassed the vast majority of reported clay‐based cathodes.

23 April 2026 in Carbon Energy
Verified
Journal Article
Open access
XGXiaowen Guo
Xiaowen Guo
SZShilin Zhang
Shilin Zhang
JBJinjin Ban
Jinjin Ban
GCGuoqin Cao
Guoqin Cao
SGShuai Guo
Shuai Guo
JHJunhua Hu
Junhua Hu
Multicomponent alloys (MCAs) have garnered significant attention in electrocatalytic applications due to their tunable multielement composition, electronic structure, and excellent stability. However, the homogeneity of MCAs results in the potential lack of distinctive catalytic sites and surface sites. This work demonstrates an MCA's design strategy and structural evolution process combining heterophase and selective defect engineering. Preferential dealloying in the bcc phase with lower ORR activity is achieved by taking advantage of the atomic arrangement structural difference of the heterophase, thus obtaining an fcc/bcc with defects ( bcc‐d ) MCA encapsulated in the carbon nanotubes (HFeCoCuAl@CNTs). The formed vacancies in the bcc‐d generate the unsaturated coordination of adjacent Fe/Co active sites and optimize the electronic structure. The synergistic catalysis of the fcc / bcc‐d accelerates all steps of the 4e − ORR. Therefore, HFeCoCuAl@CNTs exhibits the excellent electrocatalytic activity and stability in ORR (half‐wave potential: 0.823 V) and OER ( E j=10 : 344 mV) under alkaline conditions. Using the commercial Pt/C as a comparison, the HFeCoCuAl@CNTs‐based zinc–air batteries deliver the higher specific capacity of 814 mAh g Zn −1 , power density of 144.8 mW cm −2 , and long‐term stability exceeding 780 h. These findings provide unique ideas for designing MCA electrocatalysts suitable for high‐performance zinc–air batteries.

25 July 2026 in Advanced Energy Materials
Verified
Journal Article
Open access
PDF file
FLFanfan Liu
Fanfan Liu
LHLinru He
Linru He
XGXinyue Gao
Xinyue Gao
SGShuai Guo
Shuai Guo
DLDabing Li
Dabing Li
JHJunhua Hu
Junhua Hu
Designing cathode materials that can synergistically store ions with significantly different charge densities and ionic radii poses a critical challenge in the ongoing development of Mg 2+ /Li + hybrid batteries (MLHBs). MXene‐based materials with vacancy defects offer promise, yet conventional monovacancy strategies cannot balance capacity and reaction kinetics. Herein, an innovative dual‐anion (Se, O) vacancy engineering strategy is proposed and constructed a quantum dot (QD) Ti 3 C 2 MXene heterostructure (QD@V Se,O ‐Ti 3 C 2 ). Benefiting from (i) the quantum confinement effect induced by QD TiO 2 , which modifies the electronic band structure and improves interfacial charge transfer, (ii) dual‐anion vacancies that establish a complementary charge environment, providing electrostatic shielding to lower Mg 2+ diffusion barriers and facilitate charge compensation, and (iii) in situ formed TiSe 2 layers combined with strong Se─C bonds, which ensure rapid ion/electron transport and maintain structural integrity. The QD@V Se,O ‐Ti 3 C 2 cathode delivers an ultra‐high capacity (705 mAh g −1 at 50 mA g −1 ) and outstanding cycling stability with 70% capacity retention after 2300 cycles at 1000 mA g −1 . The synergy among quantum‐confined, charge compensation and shielding effects, and interfacial electronic structure achieved unprecedented Mg 2+ /Li + co‐adsorption stability and rapid kinetics. This work establishes a new paradigm of QD‐enhanced multi‐anion vacancy engineering for next‐generation multivalent‐ion batteries.