6 March 2019 in Chemistry of Materials
To this day, engineering nanoalloys beyond bimetallic compositions has scarcely been within the scope of physical deposition methods due to the complex, non-equilibrium processes they entail. Here, we report a gas-phase synthesis strategy for the growth of multi-metallic nanoparticles: magnetron-sputtering inert-gas condensation from neighboring mono-elemental targets provides the necessary compositional flexibility, while in-depth atomistic computer simulations elucidate the fast kinetics of nucleation and growth that determine the resultant structures. We fabricated consistently trimetallic Au-Pt-Pd nanoparticles, a system of major importance for heterogeneous catalysis applications. Using high-resolution transmission electron microscopy we established their physical and chemical ordering: Au/Pt-rich core@Pd-shell atomic arrangements were identified for particles containing substantial amounts of all elements. Decomposing the growth process into basic steps by molecular dynamics simulations we identified a fundamental difference between Au/Pt and Pd growth dynamics: Au/Pt electronic arrangements favor the formation of dimer nuclei instead of larger-size clusters, thus significantly slowing down their growth rate. Consequently, larger Pd particles formed considerably faster and incorporated small Au and Pt clusters by means of in-flight decoration and coalescence. A broad range of icosahedral, truncated-octahedral, and spheroidal FCC trimetallic nanoparticles were reproduced in simulation, in good agreement with experimental particles. Comparing them with their expected equilibrium structures obtained by Monte Carlo simulations, the particles were identified as metastable, due to out-of-equilibrium growth conditions. We aspire that our in-depth study will constitute a significant advance towards establishing gas-phase aggregation as a standard method for the fabrication of complex nanoparticles by design.
1 October 2020 in Sensors and Actuators B: Chemical
2 October 2019 in ACS Nano
Surface charge and charge transfer between nanoclusters and oxide supports are of paramount importance to the catalysis, surface plasmonics, and optical energy harvesting areas. At present, high-energy X-rays and theoretical investigation are always required to determine the chemical state changes in the nanoclusters and the oxide supports, as well as the underlying transfer charge between them. This work presents the idea of using chrono-conductometric measurements to determine the chemical states of the Ru nanoclusters on CuO supports. Both icosahedral and single-crystal hcp Ru nanoclusters were deposited through gas-phase synthesis. To study the charge transfer phenomenon at the interface, a bias was applied to cupric oxide nanowires with metallic nanoclusters decoration. In situ conductometric measurements were performed to observe the evolution of Ru into RuOx under heating conditions. Structural elucidation techniques such as transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and Kelvin probe force microscopy (KPFM) were employed to study the corresponding progression of structure, chemical ordering, and surface potential, respectively, while Ru(0) was oxidized to RuOx on the supporting oxide surface. Experimental and theoretical investigation of charge transfer between nanocluster and oxide support highlighted the importance of metallic character and structure of nanoclusters on the interfacial charge transfer. Thus, allowing the investigation of surface charge behavior on oxide supported catalysts, in situ, during catalytic operation via conductometric measurements.
1 October 2020 in Biosensors and Bioelectronics
22 November 2019 in Scientific Reports
Metal oxide semiconductor nanowires have important applications in label-free biosensing due to their ease of fabrication and ultralow detection limits. Typically, chemical functionalization of the oxide surface is necessary for specific biological analyte detection. We instead demonstrate the use of gas-phase synthesis of gold nanoparticles (Au NPs) to decorate zinc oxide nanowire (ZnO NW) devices for biosensing applications. Uniform ZnO NW devices were fabricated using a vapor-solid-liquid method in a chemical vapor deposition (CVD) furnace. Magnetron-sputtering of a Au target combined with a quadrupole mass filter for cluster size selection was used to deposit Au NPs on the ZnO NWs. Without additional functionalization, we electrically detect DNA binding on the nanowire at sub-nanomolar concentrations and visualize individual DNA strands using atomic force microscopy (AFM). By attaching a DNA aptamer for streptavidin to the biosensor, we detect both streptavidin and the complementary DNA strand at sub-nanomolar concentrations. Au NP decoration also enables sub-nanomolar DNA detection in passivated ZnO NWs that are resilient to dissolution in aqueous solutions. This novel method of biosensor functionalization can be applied to many semiconductor materials for highly sensitive and label-free detection of a wide range of biomolecules.
22 May 2014 in ACS Applied Materials & Interfaces