Mengfei Xiong

Mengfei Xiong

Auto-generated profile, based on publicly available information

Mengfei Xiong

Key Laboratory of Instrumentation Science and Dynamic Measurement

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 October 2018 in IEEE Antennas and Wireless Propagation Letters
Verified
Journal Article
Closed access
HXHongcheng Xu
Hongcheng Xu
BZBinzhen Zhang
Binzhen Zhang
JDJunping Duan
Junping Duan
JCJianli Cui
Jianli Cui
YXYongqing Xu
Yongqing Xu
QJQinyin Jia
Qinyin Jia
This paper presents the design for three-dimensional polymeride (3D) printing and printed circuit board (PCB) fabrication, and full experimental verification of a conical conformal array antenna with wide solid angle switching beam by a radio-frequency (RF) semiconductor switch (RFSS) configuration. The conical conformal array antenna (CCAA) consists of eight linear array antennas with uniform circumferential arrangement around the conical surface. Only one linear array antenna (LAA) out of eight arrays is individual excited operating each time by the RF semiconductor switch connected the ports of the 1 to 8 power dividers in order to achieve the requirement of beam-switching. The conical conformal array antenna with beam-switching feeding network operates at 4.8 GHz according to the fifth-generation (5G) band requirements. Both the wide solid scanning angle of 0-218° in H-plane and the halfpower bandwidth (HPBW) with that lower than 16° in E-plane are achieved. When the realized gain of each linear array antenna is over 10 dBi, the measured peak gain of the final antenna can reach about over 11 dBi and the average radiation efficiency can reach 59.5%. This conical conformal array antenna with wide solid angle beam-switching and the high gain property has potential for reducing the signal-to-noise ratio and integration with 5G communication systems.

1 January 2019 in IEEE Access
Verified
Journal Article
Open access
QJQinyin Jia
Qinyin Jia
HXHongcheng Xu
Hongcheng Xu
MXM. F. Xiong
M. F. Xiong
BZBinzhen Zhang
Binzhen Zhang
JDJunping Duan
Junping Duan

23 April 2020 in International Journal of Antennas and Propagation
Verified
Journal Article
Open access
PDF file
MXMengfei Xiong
Mengfei Xiong
JDJunping Duan
Junping Duan
BZBinzhen Zhang
Binzhen Zhang
A simplified notched design method for the Vivaldi antenna is exhibiting high frequency-band-selectivity characteristics. By suitably introducing half-wavelength resonator (HWR) and complementary capacitively loaded loop (CCLL), the notched-band selectivity is promoted while maintaining the wide impedance bandwidth of the antenna applicable for wireless communications. HWR is bent in the middle to focus the first notch pole, and the second notch pole is obtained by CCLL on the radiating patch. Additionally, the resonant frequency of the notched pole can be determined by the position and size of two loaded resonators in theoretical analysis, thereby realizing a wideband antenna with the desired notched band. Finally, the Vivaldi antenna of loading resonator was fabricated to verify the feasibility of this new method. Measured and simulated experimental results reveal that the antenna exhibits directional pattern in the passband, low gain at the band-rejection, and excellent selectivity within a frequency range. The simulation and measurement results are in good agreement. The proposed antenna achieves S11<−10 dB in 2.6–13.7 GHz and a notch band from 4.49 to 6.64 GHz to reject IEEE 802.11a and HIPERLAN/2 frequency band. Moreover, the proposed antenna has good frequency selectivity, and its gain is good enough in the passband with peak gain up to 10.8 dBi. This antenna design presents frequency suitability, demonstrating that a UWB antenna with a controllable notched band has been realized.