20 April 2020 in Traffic Injury Prevention
Objective: Drivers have difficulty deciding whether to stop at the stop line or proceed through the intersection at the onset of the circular yellow (CY) indication. The purpose of this study was to understand how drivers distribute their visual attention when the traffic signal turns to the CY indication at high-speed signalized intersections, and whether factors such as time to stop line, headway or following vehicle type, influence overt visual attention. Method: Data included eye-tracking metrics from 45 participants during a 24-scenario driving simulator experiment. Three areas of interest (AOIs) were defined (traffic signal, rear view mirror, and side view mirrors). Results: Results showed that while the CY indication was displayed, total fixation durations (TFDs) were highest on the traffic signal (626 s), lower for the rear view mirror (50 s), and lowest for the side view mirrors (3 s). Repeated-measures ANOVAs indicated that the type of following vehicle influenced TFDs. Being followed by a heavy vehicle resulted in drivers shifting their fixations away from the traffic signal. Drivers fixated on the traffic signal more when followed by a passenger car than they did when followed by a heavy vehicle. Additionally, higher time to stop lines resulted in greater TFDs on the traffic signal. Conclusions: This study highlights the importance of understanding the fixation behavior of drivers and the factors that influence drivers’ visual attention. These findings could guide future efforts by the transportation community to involve drivers in training programs to emphasize the risks associated with ignoring rear view mirrors during their response to CY indications.
1 September 2021 in Journal of Construction Engineering and Management
Vehicle speed in work zones is a significant concern to state transportation agencies and their construction partners. Prior research indicates that law enforcement vehicles within a work zone with active flashing lights result in reduced vehicle speeds. Placement of flashing blue lights on construction equipment during nighttime construction work has also been identified as a potential control measure to reduce speeds. The goal of this research study is to determine the impact of flashing blue lights on construction equipment on the speed of passing vehicles in mobile work zones. The research design consisted of a controlled experiment involving flashing blue lights mounted on the rear of a paver during mainline paving operations on three case study projects on high speed roadways at night in Oregon. Vehicle speed data were collected during multiple work shifts for each case study, both with and without the flashing blue lights on. The experimental results reveal that vehicle speed is affected by the presence of flashing blue lights during nighttime work. With the blue lights flashing and at distances upstream of the paver where the driver can see and react to the blue lights, mean vehicle speeds tended to be slower than when the blue lights were off. Closer to, immediately adjacent to, and downstream of the paver, the difference in the mean speed with the blue lights on was typically less or not significant; in some cases and mostly downstream of the paver location, the mean speeds were higher with the blue lights on than with the blue lights off. The speed differential (i.e., the speed prior to the work zone minus the speed in the work zone) was measured as greater with the blue lights turned on than with the blue lights off. The results support construction contractors and state departments of transportation for decision making about the use of flashing blue lights on equipment in work zones. The researchers recommend using flashing blue lights on paving equipment during nighttime operations if allowed by local laws to reduce the speed in the work zone and increase worker and driver safety. This research contributes to the construction industry by providing quantitative evidence of the extent to which flashing blue lights mounted on paving equipment impact vehicle speeds in work zones. Recently, all stakeholders, including the Oregon Department of Transportation, law enforcement, and contractors, have agreed to use the flashing blue lights on paving equipment in Oregon during the 2021 construction season.
1 May 2020 in Journal of Surveying Engineering
Unmanned aerial systems (UASs) are an emerging technology being used in many fields, including surveying engineering. When UASs are used for these activities, they may operate in close proximity to active traffic. UASs could be distracting to drivers and increase safety concerns in these situations. Currently, there are no temporary traffic control (TTC) signs approved by the Manual on Uniform Traffic Control Devices (MUTCD) to specifically inform drivers of roadside UASs. For this study, new UAS TTC signs were designed and a questionnaire was developed to explore perspectives on UAS specific TTC. Participants drove in a high-fidelity driving simulator, which measured speed reduction, as participants drove past various configurations of TTC elements in advance of a roadside UAS operation. The results showed that drivers do support the use of UAS specific TTC signs. Speed data from the driving simulator showed that a TTC configuration of two advanced signs caused drivers to decrease their speed by an average of more than than when no TTC was present, while also inducing this deceleration at the most gradual rate.