This study was conducted to determine the effect of composite flour (CF) constituents and different extrusion temperatures on the production of analog rice and community perceptions about the produced rice. CF was produced by mixing modified cassava flour (Mocaf) and snakehead fish flour (SF) in the following ratios: 100:0; 97:3; 94:6; 91:9; and 88:12. Analog rice was then extruded from CF at the following temperatures: 50, 70, and 90°C. The analog rice was tested for physical properties (bulk density and cooking time), chemical properties (nutrient content), and organoleptic properties. The results showed that CF and extrusion temperature affect the nutrient content of analog rice. The best analog rice formulation constituted of CF with Mocaf:SF ratio of 91:9 and extrusion temperature of 70°C, and contained 14.34% water, 0.85% ash, 71.83% carbohydrate, 11.24% protein, 1.12%, calcium 1,113 ppm, and 2.43% dietary fiber. This study included 42 respondents aged 20–23 years, including 20 males and 22 females. All the respondents showed acceptance for the analog rice, suggesting that it could substitute ordinary rice as a staple food.
Komposit merupakan gabungan dari dua atau lebih bahan yang menghasilkan efek sinergis. Komposit dapat dibuat dari polimer sebagai matriks dan serat alam sebagai bahan penguat. Pada penelitian ini komposit dibuat dari styrofoam bekas dan serat ijuk aren. Styrofoam merupakan salah satu jenis polimer yang sulit terdegradasi secara alami, sedangkan serat ijuk aren merupakan serat alam yang mudah diperoleh di Indonesia. Pembuatan komposit dilakukan dengan alat hot press pada berbagai perbandingan massa styrofoam dan serbuk ijuk aren (10:90; 20:80; 30:70; 40:60; dan 50:50). Karakterisasi komposit yang dihasilkan meliputi uji kekuatan mekanik, kerapatan, daya serap air, mikrostruktur, dan gugus fungsional. Komposit mempunyai kekuatan mekanik tertinggi sebesar 90,26 kgf/cm2 pada perbandingan massa styrofoam dan serbuk ijuk aren 30:70. Semakin tinggi kandungan styrofoam dalam komposit maka kerapatan komposit akan semakin meningkat dan daya serap air komposit semakin menurun. Komposit mempunyai struktur yang homogen dan gugus fungsional yang berasal dari styrofoam dan serat ijuk aren. Composite is a combination of two or more materials that produce a synergistic effect. Composite can be made from polymers as matrices and natural fibers as reinforcing agents. In this study, composite were synthesized from used styrofoam and sugar palm fiber. Styrofoam is one type of polymer that is difficult to degrade naturally, whereas sugar palm fiber is a natural fiber that is easily obtained in Indonesia. Composite synthesis was done using hot press equipment at various mass ratio of styrofoam to sugar palm fiber powder (10:90; 20:80; 30:70; 40:60; and 50:50). Characterization of obtained composites covered tests of mechanical strength, density, water absorption, microstructure, and functional groups. Composite had the highest mechanical strength of 90.26 kgf/cm2 at the mass ratio of styrofoam to sugar palm fiber powder of 30:70. The increase of the styrofoam content in composite caused the increase of composite density and the decrease of composite water absorption. Composite had homogeneous structure and functional groups derived from styrofoam and sugar palm fiber.
20 October 2020 in Journal of Vocational Studies on Applied Research
Biodiesel is an alternative fuel which is generally produced from the transesterification process between vegetable oil and methanol, ethanol, or butanol with the help of a catalyst which aims to speed up the reaction. The raw material for making biodiesel, namely renewable vegetable oil, also sees Indonesia as a tropical country so that biodiesel can be produced on a large scale and is environmentally friendly. Vegetable oil can be classified into two, namely edible oil (food) and non edible oil (non-food). The research was conducted using non-edible vegetable oil, namely kemiri sunan oil, which was carried out using a two-stage transesterification method. This research was conducted to determine the optimization of the ratio of oil and methanol (1: 4; 1: 5; 1: 6), temperature (55⁰C, 60⁰C, 65⁰C) and reaction time (15 minutes, 30 minutes, 45 minutes) in making biodiesel from kemiri sunan oil, where the experimental results obtained the highest yield value of 82.79%. In the experiment, analysis of density, viscosity, moisture content and cetane number was also carried out. The results showed that the viscosity and cetane number obtained did not meet SNI for biodiesel.
Background: The majority of people in Indonesia make rice as a staple food. From the large consumption of paddy rice, there is an alternative to overcome dependence on rice by developing analog rice. Analog rice is artificial rice with raw materials that contain high carbohydrates. Raw materials for making analog rice must contain structural forming materials such as dispersed phases, thickeners, flavor enhancers, and leavening agents. Some of the main ingredients of analog rice include cassava, gembili, and sweet potatoes.Objective: The purpose of this study was to determine the content and types of local ingredients that can be used to make analog rice as a substitute food for paddy riceMethod: This research uses Systematic Literature Review from national and international journalsResults: There are various materials with perfect nutritional content that must be contained in analog rice.Conclusion: Analog rice is an alternative solution to the problem of the Indonesian people's dependence on rice. Analog rice must be considered a constituent material to have a perfect nutritional content. Indonesian local ingredients such as cassava, gembili tubers, and sweet potatoes can be used as analog rice staples
Gelatin is a protein derivative product resulting from the collagen breakdown in a material. The protein content in dried grasshoppers, which are halal insects, reaches 40%. Hence, they have the potential to be produced as a substitute for non-halal gelatin. This study aims to determine the effect of various acid and base solvents and soaking time in the demineralization process on the characteristics of the gelatin. This study used a completely randomized design. The treatment of solvent types in the demineralization process used 6% HCl, 1% citric acid, 3% acetic acid, pineapple extract, and NaOH; while soaking times for treatment were 24 hours, 36 hours, and 48 hours. Each soaking time and solvent type in the demineralization process gave a significant effect on the yield value (P < 0.05). Demineralization treatment using 6% HCl for 48 hours showed gelatin with the best yield than other treatments, i.e., gelatin with a moisture content of 9.93%, ash content of 1.11%, and pH 5. The characteristics of gelatin in this study are under SNI 06-3735 of 1995.