I-Ting Lin

I-Ting Lin

Auto-generated profile, based on publicly available information

I-Ting Lin

Division of New Panel-level Packaging, Corporate R&D Advanced Semiconductor Engineering (ASE) Group, Kaohsiung City, Taiwan

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 August 2016 in Interface Focus
Verified
Journal Article
Open access
TWTiesheng Wang
Tiesheng Wang
MFMeisam Farajollahi
Meisam Farajollahi
YCYeon Sik Choi
Yeon Sik Choi
ILI-Ting Lin
I-Ting Lin
JMJean E. Marshall
Jean E. Marshall
SSStoyan K. Smoukov
Stoyan K. Smoukov
Electromechanical coupling in electroactive polymers (EAPs) has been widely applied for actuation and is also being increasingly investigated for sensing chemical and mechanical stimuli. EAPs are a unique class of materials, with low-moduli high-strain capabilities and the ability to conform to surfaces of different shapes. These features make them attractive for applications such as wearable sensors and interfacing with soft tissues. Here, we review the major types of EAPs and their sensing mechanisms. These are divided into two classes depending on the main type of charge carrier: ionic EAPs (such as conducting polymers and ionic polymer–metal composites) and electronic EAPs (such as dielectric elastomers, liquid-crystal polymers and piezoelectric polymers). This review is intended to serve as an introduction to the mechanisms of these materials and as a first step in material selection for both researchers and designers of flexible/bendable devices, biocompatible sensors or even robotic tactile sensing units.

1 June 2021
Verified
Conference Paper
Closed access
CLChien-Lung Liang
Chien-Lung Liang
MTMin-Yan Tsai
Min-Yan Tsai
YLYung-Sheng Lin
Yung-Sheng Lin
ILI-Ting Lin
I-Ting Lin
圣杨圣文 杨
圣文 杨
KLKwang-Lung Lin
Kwang-Lung Lin
We presented in this article an in situ electromigration behavior in a novel Cu tall pillar/Cu via interconnect. A Cu tall pillar connecting to a single Cu via for joining the fan-out Cu redistribution lines (RDLs) was introduced for high-power device applications. The novelty of this study was to design a special ladder-shaped Cu tall pillar for the purpose of the fan-out effect of high-density electric current. The in situ SEM (scanning electron microscope) microstructure investigation during the electromigration experiment provided interesting information for the reliability evaluation and in-depth mechanism exploration of the electromigration behavior in the novel Cu interconnect. A stepwise electromigration experiment was conducted at an initial 2.5 A electric current, approximately 10 5 to 10 6 A/cm 2 current density for the components in the Cu interconnect, followed by a larger current input of 3 A. Electrons flowed from the fan-out Cu RDL (cathode) through the Cu via to the Cu tall pillar and the connecting Cu line (anode). The investigations revealed the dynamic void nucleation and coalescence phenomena in the cathodic Cu via during the early stage electromigration. Cu consumption due to the surface diffusion mechanism also occurred on the sidewall of the Cu via. Grain rotation within the Cu interconnect as a result of the electromigration-induced toque was also observed. The considerable mass loss in the Cu via upon electromigration caused a near-collapse microstructure of the Cu interconnect, leading to a potential reliability concern. Electromigration also induced the formation of Cu hillocks on the anodic Cu line, revealing a typical polarity effect. The Cu hillocks were derived from the predominant consumption of the Cu tall pillar rather than the Cu via or the Cu RDL due to the critical mass transport. The voids formed within the Cu tall pillar mostly appeared with a triple junction grain boundary morphology for the Cu consumption, suggesting a grain-boundary-related Cu migration mechanism. The grain boundary diffusion phenomenon was proposed to be the predominant mechanism for explaining the electromigration-induced void and hillock formation in the novel Cu tall pillar/Cu via interconnect.

2 October 2017 in Scientific Reports
Verified
Journal Article
Open access
PDF file
ILI-Ting Lin
I-Ting Lin
TWTiesheng Wang
Tiesheng Wang
FZFenghua Zhang
Fenghua Zhang
SSStoyan K. Smoukov
Stoyan K. Smoukov
Electrically deformable surfaces based on dielectric elastomers have recently demonstrated controllable microscale roughness, ease of operation, fast response, and possibilities for programmable control. Potential applications include marine anti-biofouling, dynamic pattern generation, and voltage-controlled smart windows. Most of these systems, however, exhibit limited durability due to irreversible dielectric breakdown. Lowering device voltage to avoid this issue is hindered by an inadequate understanding of the electrically-induced wrinkling deformation as a function of the deformable elastic film thickness. Here we report responsive surfaces that overcome these shortcomings: we achieve fault-tolerant behavior based on the ability to self-insulate breakdown faults, and we enhance fundamental understanding of the system by quantifying the critical field necessary to induce wrinkles in films of different thickness and comparing to analytical models. We also observe new capabilities of these responsive surfaces, such as field amplification near local breakdown sites, which enable actuation and wrinkle pattern formation at lower applied voltages. We demonstrate the wide applicability of our responsive, fault-tolerant films by using our system for adjustable transparency films, tunable diffraction gratings, and a dynamic surface template/factory from which various static micropatterns can be molded on demand.