21 July 2021 in IEEE Transactions on Antennas and Propagation
A dual-beam filtering patch antenna with two absorptive band-edge radiation nulls and four reflective stopband radiation nulls is proposed. By loading a pair of T-shaped metallic strip underneath the radiating patch, a modified TM 22 mode with TM 20 -like radiation pattern is obtained, which combines with the TM 20 mode of the radiating patch, generating a wide operating band with symmetrical dual-beam radiation pattern. Two reflective radiation nulls are generated in both upper and lower stopbands for suppressing the out-of-band radiation. Through embedding two pairs of shorted small patch in the radiating patch, one absorptive radiation null combining with one absorptive resonant mode is produced at each band edge to absorb the band-edge incident energy, leading to a reduced reflection and sharp roll-off at both band edges, and therefore, the transceiver can be protected. With a total height of $0.038~\lambda _{0}$ , a prototype is designed, fabricated, and measured, showing a −10 dB impedance bandwidth from 4.63 to 6.10 GHz with sharp band-edge roll-off, two radiation beams directed at ±40° with an in-band gain of 6.0 dBi, and high out-of-band suppression of over 15 dB.
10 November 2021 in IEEE Transactions on Antennas and Propagation
A planar dual-band dual-sense circularly polarized (CP) microstrip array is proposed. This array is implemented on a single-layer substrate and easily extended to the design of a larger array. A new antenna element is exploited by symmetrically placing the nonradiative resonators on four side edges of a square patch. A quantitative design method is proposed based on the equivalent circuit model of the antenna element. For given two operating frequencies, the required design parameters of the patch and nonradiative resonators can be calculated. Theoretical magnitude ratio and phase difference responses of two far-field components, as well as axial ratio responses under different parameters, are presented to reveal the characteristics of the antenna element. Full-wave simulation results are found to agree well with the theoretical ones. To further validate the effectiveness, a $2 \times 2$ element dual-band dual-sense CP array operating at 2.40 and 2.68 GHz is designed, fabricated, and measured, where a small frequency ratio of 1.117 is achieved. The measured realized gains in the low and high bands are 11.7 and 11.8 dBi, respectively, which are approximately equal.
22 March 2023 in IEEE Antennas and Wireless Propagation Letters
With wide impedance bandwidth (IBW), wide axial-ratio bandwidth (ARBW), stable AR beamwidth, and stable half-power beamwidth (HPBW), a dual-circularly-polarized (DCP) crossed-dipole antenna is proposed. Each dipole consisting of two patches is fed by a pair of parallel transmission line, leading to a wide IBW. To enhance the ARBW and AR beamwidth, a quadrature wideband coupler is used, and the overlapping bandwidth of IBW and ARBW is up to 100%. The quadrature coupler is integrated with two pairs of parallel transmission line, and are printed on two substrates, which are squeezed into the space between the radiators and reflector, resulting into a compact antenna structure. With a total height of 0.016 λ L , a prototype is fabricated and measured, showing 1.5-VSWR IBW of larger than 104% for both Left-handed CP (LHCP) and Right-handed CP (RHCP), 3-dB ARBW of up to 100% both for LHCP and RHCP, and port-to-port (polarization) isolation of lager than 30 dB in 1.70 - 2.82 GHz, so the effective bandwidth (EBW) is about 50% (1.70 - 2.82 GHz). 3-dB AR beamwidth of 76° ± 5°, stable DCP characteristics with average gain of 7.2 dBi and HPBWs of 67° ± 4° are achieved.
6 June 2018 in IEEE Sensors Journal
Radio frequency identification (RFID) tag antenna based passive wireless sensors are receiving increasing attentions for structural health monitoring (SHM) in large-scale infrastructure. For permanently-installed monitoring, robustness to measurement variation including environmental conditions is a practical issue. This paper retrospects the communication principle of magnetic resonant coupling (MRC) for low frequency (LF) passive wireless RFID antenna sensors. The influence of communication is uncovered and essentially separated from sensing through two steps: sweep (source) frequency to capture the system behavior, i. e., resonance frequency range; multiple feature extraction, fusion, and selection in conjunction with normalization for the selected time-domain feature of peak to peak (P2P). By this way, the robustness of the low-cost RFID sensing system is enhanced. The proposed method is validated by the case study in open crack detection and characterization under varied measurement conditions.
31 July 2023 in IEEE Antennas and Wireless Propagation Letters
A circularly polarized (CP) filtering patch antenna with a strip network is proposed, which utilizes two substrates with space of 6 mm. A slotted loop is placed around a slotted patch on the top side of the upper substrate to excite two CP modes. A strip network printed on the bottom side of the upper substrate produces the third CP mode and a high-frequency radiation null, while a low-band-edge and a high-band-edge radiation nulls are excited by a shorted pin. The three CP modes form a wider axial ratio (AR) bandwidth than the impedance bandwidth. The impedance matching bandwidth and the out-of-band radiation suppression level are furtherly improved by another slots etched on the slotted loop and on the radiation patch. The antenna prototype is fabricated, and the measured results show that the -10 dB impedance matching bandwidth is 21.6% from 3.26 to 4.05 GHz, the 3-dB AR bandwidth is 23.1% from 3.14 to 3.96 GHz, the in-band peak gain is up to 7.6 dBic, and the radiation suppression levels are higher than 23 and 14 dB for the low- and high-frequency stopbands, respectively. These features make the proposed antenna a promising candidate for 5G NR n78 band mobile communication systems.