10 April 2019 in Machinery Energetics
NUNational University of Life and Environmental Sciences of Ukraine
National University of Life and Environmental Sciences of Ukraine
В статті розглянуто кочення плоскої фігури у вигляді рівностороннього багатокутника по криволінійному профілю. Профіль є періодичним і утворюється послідовним повторенням дуги симетричної кривої в прямолінійному напрямку. Рівняння кривої, з дуги якої конструюється криволінійний про-філь, знайдено за умови, що центр багатокутника при його коченні по профілю, має рухатися по прямій лінії. Кочення відбувається за відсутності ковзання, тому довжина дуги кривої дорівнює довжині сторони багатокутника. При з’єднанні сусідніх дуг профілю утворюється точка звороту, у якій можна провести дотичні до обох дуг. Кут між цими дотичними має бути рівним кутові між сусідніми сторонами багатокутника. Наприклад, для квадрата цей кут є прямим. Виконання цієї умови необхідно для забезпечення плавного перекочування багатокутника при походженні його вершини через точку звороту.На основі встановлення залежностей між сторо-нами і кутами розглянутих фігур, одна з яких перекочується по іншій, було складено диференціальне рів-няння першого порядку, яке має аналітичний розв’язок. Цим розв’язком є явне рівняння розшукуваної кривої. Переходом від явного до натурального рівняння з’ясовано, що знайденою кривою є відома ланцюгова лінія. Знайдено координати точок на кри-вій, які обмежують дугу потрібної довжини. Наведено вираз для визначення періоду криволінійного профілю.В статті показано доцільність застосування супровідного тригранника кривої для перевірки досто-вірності отриманого результату. При русі тригранни-ка вздовж плоскої кривої один його орт є дотичним до неї, а другий – перпендикулярний до першого. В сис-темі цих двох взаємно перпендикулярних ортів (доти-чної і головної нормалі) задається такий відносний рух точки, який моделює перекочування дотичної по кривій. Сума двох рухів – відносного руху точки в системі тригранника і переносного руху самого три-гранника по кривій – дає абсолютну траєкторію точ-ки. Для застосування такого підходу необхідно мати рівняння кривої у функції довжини власної дуги. За таке рівняння було взято натуральне рівняння ланцю-гової лінії. Було складено рівняння відносного руху точки, яка є центром багатокутника, в рухомій систе-мі супровідного тригранника. При додаванні відносного і переносного рухів було отримано абсолютну траєкторію, якою є пряма лінія. Цим було підтвер-джено той факт, що розшукуваною кривою є саме ланцюгова лінія. В статті сформульовано відповідне твердження. Також показано, що число сторін багато-кутника повинне бути більше трьох. Для трикутника кочення стає неможливим в момент проходження точки звороту криволінійного профіля.
30 January 2020 in Machinery Energetics
NUNational University of Life and Environmental Sciences of Ukraine
National University of Life and Environmental Sciences of Ukraine
Кочення розгортного гелікоїда по своєму згинанню
17 December 2020 in APPLIED GEOMETRY AND ENGINEERING GRAPHICS
If two linear surfaces move one after another without sliding, then they can be considered as axoids of a solid body that performs a corresponding motion in space. If the axoids are cylindrical surfaces, then the study of their rolling can be replaced by the study of the rolling of centroids - curves of the orthogonal cross section of these cylindrical surfaces. Usually the rolling of a moving centroid on a stationary one is considered. However, there are cases when centroids roll one after another, while rotating around fixed centers. Examples of round centroids are circles, non-round - congruent ellipses, in which the centers of rotation are foci. In both cases, the center-to-center distance is constant. The point of contact of the circles is located at the center distance and is stationary during their rotation, and for ellipses it "floats" on this segment. In the article [1] the congruent centroids formed by symmetric arcs of a logarithmic spiral are considered. The centers of rotation of the centroid are the poles of the spirals. A characteristic feature of logarithmic spirals is that they intersect all radius vectors emanating from the pole at a constant angle. For a sphere, the prototype of a logarithmic spiral is a loxodrome, which crosses all the meridians at a constant angle and twists around the pole of the sphere. The paper hypothesizes that closed spherical curves formed from arcs of loxodrome, like centroids from arcs of a logarithmic spiral on a plane, can also roll around axes intersecting in the center of the sphere. If these closed curves are connected by rectilinear segments with the center of the sphere, then two cones are formed - axoids of non- circular conical wheels. This hypothesis is based on the fact that with an infinite increase in the radius of the sphere, its surface around the pole turns into a plane, and the meridians - in straight lines emanating from the pole. Accordingly, the loxodrome is transformed into a logarithmic spiral. The article shows that the hypothesis is confirmed. Axoids of non- circular wheels are built in it, the axes of which intersect at right angles. The expression of the arc length of the loxodrome is found and it is shown that when the conical axoids rotate at appropriate angles around their axes, the contact curves pass straight paths. This means that the rolling of the axis occurs without sliding.
4 December 2023 in Bulletin of Sumy National Agrarian University. The series: Mechanization and Automation of Production Processes
ТВТетяна Миколаївна Воліна
ВНВіктор Миколайович Несвідомін
Віктор Миколайович Несвідомін
After crushing the green mass with a cutting drum in forage harvesters, it must be loaded into a vehicle. A silo pipeline of forage harvesters provides the required trajectory of the crushed mass from the drum to the vehicle. The trajectory of particle movement is determined by the shape of a flat curve – the axis of the silo pipeline. The shape of its axis affects the transportation process. The main characteristic on which this process depends is the dependence of the curvature on the length of the arc of the axis. With constant curvature, the axis is the arc of a circle. However, this shape of the axis may not satisfy the design requirements, since the height of the silo pipeline will be too high during transporting mass over a considerable distance. It is possible to control the shape of the axis using the specified dependence of the curvature on the length of the axis. The curvature should change smoothly from the minimum value to the maximum and then should decrease. It prevents material from sticking when it meets the silo pipeline. In addition, by specifying the law of change of curvature from the length of the axis, it is possible to give the desired shape of the silo pipeline. Different approaches are used for the analytical description of the transportation of technological material, which consists of individual particles. It can be explained by the complexity of the processes that occur when particles interact with each other. Therefore, the transportation of a single particle is often considered, the movement of which can be described analytically. The resulting dependencies can in a certain way be transferred to the technological material. This research analytically shows the importance of the regularity of changes in the curvature of the axis of the silo pipeline or the trajectory of particle movement. A differential equation of the movement of a single particle on the surface of the silo pipeline has been formulated. It is shown that for an axis in the form of a circle, the differential equation has an analytical solution, for other cases numerical methods should be used. A comparative analysis of the process of transporting the crushed mass in silo pipelines with different axis shapes was made. Solutions of differential equations are accompanied by corresponding graphical illustrations.
15 August 2019 in Machinery Energetics
NUNational University of Life and Environmental Sciences of Ukraine
National University of Life and Environmental Sciences of Ukraine
SISeparated Subdivision of National University of Life and Environmental Sciences of Ukraine «Berezhany Agrotechnical Institute»
Separated Subdivision of National University of Life and Environmental Sciences of Ukraine «Berezhany Agrotechnical Institute»
+1
Транспортування частинки горизонтальним шнеком, обмеженим співвісним нерухомим циліндром