Artem Shelemin

Artem Shelemin

Auto-generated profile, based on publicly available information

Artem Shelemin

Department of Engineering Physics, Polytechnique Montréal, Montréal, Québec H3T 1J4, Canada

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 September 2018 in Nanoscale
Verified
Journal Article
Closed access
PDF file
JKJaroslav Kousal
Jaroslav Kousal
ASArtem Shelemin
Artem Shelemin
MSMatthias Schwartzkopf
Matthias Schwartzkopf
OPOleksandr Polonskyi
Oleksandr Polonskyi
JHJan Hanuš
Jan Hanuš
Andrei ChoukourovAndrei Choukourov
Andrei Choukourov
Magnetron discharge in a cold buffer gas represents a liquid-free approach to the synthesis of metal nanoparticles (NPs) with tailored structure, chemical composition and size. Despite a large number of metal NPs that were successfully produced by this method, the knowledge of the mechanisms of their nucleation and growth in the discharge is still limited, mainly because of the lack of in situ experimental data. In this work, we present the results of in situ Small Angle X-ray Scattering measurements performed in the vicinity of a Cu magnetron target with Ar used as a buffer gas. Condensation of atomic metal vapours is found to occur mainly at several mm distance from the target plane. The NPs are found to be captured preferentially within a region circumscribed by the magnetron plasma ring. In this capture zone, the NPs grow to the size of 90 nm whereas smaller ones sized 10–20 nm may escape and constitute a NP beam. Time-resolved measurements of the discharge indicate that the electrostatic force acting on the charged NPs may be largely responsible for their capturing nearby the magnetron.

18 December 2019 in Particle & Particle Systems Characterization
Verified
Journal Article
Closed access
PDF file
ASArtem Shelemin
Artem Shelemin
PPPavel Pleskunov
Pavel Pleskunov
JKJaroslav Kousal
Jaroslav Kousal
JDJonas Drewes
Jonas Drewes
JHJan Hanuš
Jan Hanuš
Andrei ChoukourovAndrei Choukourov
Andrei Choukourov

15 September 2017 in Plasma Sources Science and Technology
Verified
Journal Article
Closed access
PDF file
JKJaroslav Kousal
Jaroslav Kousal
AKA Kolpaková
A Kolpaková
ASA Shelemin
A Shelemin
PKPavel Kudrna
Pavel Kudrna
MTM Tichý
M Tichý
HBH Biederman
H Biederman
Gas aggregation sources are nowadays rather widely used in the research community for producing nanoparticles. However, the direct diagnostics of conditions inside the source are relatively scarce. In this work, we focused on monitoring the plasma parameters and the composition of the gas during the production of the TiO x nanoparticles. We studied the role of oxygen in the aggregation process and the influence of the presence of the particles on the plasma. The construction of the source allowed us to make a 2D map of the plasma parameters inside the source.

4 March 2019 in Soft Matter
Verified
Journal Article
Closed access
PDF file
DNDaniil Nikitin
Daniil Nikitin
SMSherif Madkour
Sherif Madkour
PPPavel Pleskunov
Pavel Pleskunov
RTRenata Tafiichuk
Renata Tafiichuk
ASArtem Shelemin
Artem Shelemin
Andrei ChoukourovAndrei Choukourov
Andrei Choukourov
Copper has a strong bactericidal effect against multi-drug resistant pathogens and polyethers are known for their resistance to biofilm formation. Herein, we combined Cu nanoparticles (NPs) and a polyether plasma polymer in the form of nanocomposite thin films and studied whether both effects can be coupled. Cu NPs were produced by magnetron sputtering via the aggregation in a cool buffer gas whereas polyether layers were synthesized by Plasma-Assisted Vapor Phase Deposition with poly(ethylene oxide) (PEO) used as a precursor. In situ specific heat spectroscopy and XPS analysis revealed the formation of a modified polymer layer around the NPs which propagates on the scale of a few nanometers from the Cu NP/polymer interface and then transforms into a bulk polymer phase. The chemical composition of the modified layer is found to be ether-deficient due to the catalytic influence of copper whereas the bulk polymer phase exhibits the chemical composition close to the original PEO. Two cooperative glass transition phenomena are revealed that belong to the modified polymer layer and the bulk phase. The former is characterized by constrained mobility of polymer segments which manifests itself via a 30 K increase of dynamic glass transition temperature. Furthermore, the modified layer is characterized by the heterogeneous structure which results in higher fragility of this layer as compared to the bulk phase. The Cu NPs/polyether thin films exhibit reduced protein adsorption; however, the constrained segmental dynamics leads to the deterioration of the non-fouling properties for ultra-thin polyether coatings. The films are found to have a bactericidal effect against multi-drug resistant Gram-positive Methicillin-Resistant Staphylococcus aureus and Gram-negative Pseudomonas aeruginosa.

6 April 2020 in Surface and Interface Analysis
Verified
Journal Article
Closed access
PDF file
TKTereza Košutová
Tereza Košutová
LHLukáš Horák
Lukáš Horák
ASArtem Shelemin
Artem Shelemin
MVMykhailo Vaidulych
Mykhailo Vaidulych
JHJan Hanuš
Jan Hanuš
MDMilan Dopita
Milan Dopita

18 October 2021 in Journal of Vacuum Science & Technology A
Verified
Journal Article
Closed access
PDF file
ASArtem Shelemin
Artem Shelemin
OZOleg Zabeida
Oleg Zabeida
JKJolanta-Ewa Klemberg-Sapieha
Jolanta-Ewa Klemberg-Sapieha
LMLudvik Martinu
Ludvik Martinu
In the present work, we investigate the fundamental gas-phase processes during the application of the ion beam assisted chemical vapor deposition method for the synthesis of hybrid (organic-inorganic) optical coatings. The liquid monomer Hexamethyldisiloxane was used as a model precursor for the fabrication of low index optical films. Comprehensive diagnostic analysis has been performed by employing a combination of mass spectrometry, optical emission spectroscopy, and Langmuir probe measurements. Assessment of the correlation between the process parameters and the film growth indicated a crucial role of the ratio between the ion beam power density and the precursor flow rate in controlling the monomer fragmentation rate. Controlling these two principal process variables is proposed as an effective tool for tuning the deposition rate and the density and optical properties of the growing films.