We developed a recipe for predicting strong ground motions based on a characterization of the source model for future crustal earthquakes. From recent developments of waveform inversion of strong motion data used to estimate the rupture process, we have inferred that strong ground motion is primarily related to the slip heterogeneity inside the source rather than average slip in the entire rupture area. Asperities are characterized as regions that have large slip relative to the average slip on the rupture area. The asperity areas, as well as the total rupture area, scale with seismic moment. We determined that the areas of strong motion generation approximately coincide with the asperity areas. Based on the scaling relationships, the deductive source model for the prediction of strong ground motions is characterized by three kinds of parameters: outer, inner, and extra fault parameters. The outer fault parameters are defined as entire rupture area and total seismic moment. The inner fault parameters are defined as slip heterogeneity inside the source, area of asperities, and stress drop on each asperity based on the multiple-asperity model. The pattern of rupture nucleation and termination are the extra fault parameters that are related to geomorphology of active faults. We have examined the validity of the earthquake sources constructed by our recipe by comparing simulated and observed ground motions from recent inland crustal earthquakes, such as the 1995 Kobe and 2005 Fukuoka earthquakes.
1 May 2013 in Bulletin of the Seismological Society of America
We have constructed a short‐period source model for the 2011 Mw 9.0 Off the Pacific Coast of Tohoku earthquake using strong‐motion records at stations near the source fault. The observed strong motions contain five wavepackets that correspond to specific strong‐motion generation areas (SMGAs). The origins of the wavepackets were retrieved from the original seismograms using a semblance analysis. We determine the locations of the SMGAs based on sources extracted from the corresponding wavepackets. The short‐period source model consists of five SMGAs (SMGA1–5), which are located west of the hypocenter and along the down‐dip edge of the source fault. SMGA1 is located in the Miyagi‐Oki source region west of the hypocenter, SMGA2 in the middle Sanriku‐Oki source region north of the hypocenter, and SMGA3 in the southern Sanriku‐Oki source region west of the hypocenter. SMGA4 and SMGA5 are located near the down‐dip edge of the mainshock source fault, extending from offshore Fukushima prefecture to offshore Ibaraki prefecture. At some stations near the source fault, impulsive waves are also seen on the recorded seismograms. Ground motions corresponding to these impulsive waves cannot be accounted for using the conventional uniform SMGA model. We attempt instead to simulate the observed ground motions at the Onagawa Nuclear Power Plant at a depth of 128 m very near the source fault, using a heterogeneous source model. The impulsive waves are well simulated using the heterogeneous model with higher stress parameters within a small subarea inside the SMGAs.
The main objective of this study is to develop physics‐based constraints on the spatiotemporal variation of the slip‐rate function using a simplified dynamic rupture model. First, we performed dynamic rupture modeling of the 2019 7.1 Ridgecrest, California, earthquake, to analyze the effects of depth‐dependent stress and material friction on slip rate. Then, we used our modeling results to guide refinements to the slip‐rate function that were implemented in the Graves–Pitarka kinematic rupture generation technique. The dynamic ruptures were computed on a surface‐rupturing, planar strike‐slip fault that includes a weak (negative to low‐stress‐drop) zone in the upper 4 km of the crust. Below the weak zone, we placed high‐stress‐drop patches designed to mirror the large‐slip areas seen in various rupture model inversions of the event. The locations of the high‐stress‐drop patches and the hypocenter were varied in multiple realizations to investigate how changing the dynamic conditions affected the resulting rupture kinematics, in particular, the slip rate. From these simulations, we observed a systematic change in the shape of the slip‐rate function from Kostrov type below the weak zone to a predominantly symmetric shape within the weak zone, along with a depth‐dependent reduction of peak slip rate. We generalized these shallow rupture features into a depth‐dependent parametric variation of the slip‐rate function and implemented it in the Graves–Pitarka kinematic rupture model generator. The performance of the updated kinematic approach was then verified in 0–4 Hz simulations of the 7.1 Ridgecrest earthquake, which showed that incorporating the depth‐dependent variation in the shape of the slip‐rate function improves the fit to the observed near‐fault ground motions in the 0.5–3 s period range.
A two-stage scaling relationship of the source parameters for crustal earthquakes in Japan has previously been constructed, in which source parameters obtained from the results of waveform inversion of strong motion data are combined with parameters estimated based on geological and geomorphological surveys. A three-stage scaling relationship was subsequently developed to extend scaling to crustal earthquakes with magnitudes greater than M w 7.4. The effectiveness of these scaling relationships was then examined based on the results of waveform inversion of 18 recent crustal earthquakes (M w 5.4–6.9) that occurred in Japan since the 1995 Hyogo-ken Nanbu earthquake. The 2016 Kumamoto earthquake, with M w 7.0, was one of the largest earthquakes to occur since dense and accurate strong motion observation networks, such as K-NET and KiK-net, were deployed after the 1995 Hyogo-ken Nanbu earthquake. We examined the applicability of the scaling relationships of the source parameters of crustal earthquakes in Japan to the 2016 Kumamoto earthquake. The rupture area and asperity area were determined based on slip distributions obtained from waveform inversion of the 2016 Kumamoto earthquake observations. We found that the relationship between the rupture area and the seismic moment for the 2016 Kumamoto earthquake follows the second-stage scaling within one standard deviation (σ = 0.14). The ratio of the asperity area to the rupture area for the 2016 Kumamoto earthquake is nearly the same as ratios previously obtained for crustal earthquakes. Furthermore, we simulated the ground motions of this earthquake using a characterized source model consisting of strong motion generation areas (SMGAs) based on the empirical Green’s function (EGF) method. The locations and areas of the SMGAs were determined through comparison between the synthetic ground motions and observed motions. The sizes of the SMGAs were nearly coincident with the asperities with large slip. The synthetic ground motions obtained using the EGF method agree well with the observed motions in terms of acceleration, velocity, and displacement within the frequency range of 0.3–10 Hz. These findings indicate that the 2016 Kumamoto earthquake is a standard event that follows the scaling relationship of crustal earthquakes in Japan.