21 October 2024 in Journal of Polymer Science
The rise in environmental and health concerns has led to increasing attention to nature‐derived materials. Natural resin (NR) is secreted by pine trees, and it is a great monomer source for synthesizing biopolymers. The objective of this study is to produce terpene rosin phenolic resin (TRPR) from NR, turpentine, and phenol by applying a novel polymerization technique. An environmentally friendly and reusable catalyst (Amberlyst15) was chosen instead of traditional ones. TRPR samples were chemically characterized using Fourier transform infrared spectroscopy (FTIR), nuclear magnetic resonance spectroscopy (NMR), and gel permeation chromatography (GPC) analysis. The average molecular weight (Mw) of TRPR was detected as 560 g/mol. Artificial neural network (ANN) modeling was designed with three inputs (pressure, temperature, and terpene/NR ratio) and four outputs (reaction yield, acid value, saponification value, and softening point). The highest TRPR yield was obtained with a terpene/NR ratio of (1/2) at 80°C and under 3 atm. The lowest acid and saponification values were calculated as 90.54 and 100.11 mg KOH/g, respectively. The softening point of TRPR reached 80°C and it was suggested for use in the paper, ink, and adhesive industries.
31 December 2023 in Kahramanmaraş Sütçü İmam Üniversitesi Tarım ve Doğa Dergisi
Türkiye’de Akdeniz florasında yaygın olarak bulunan, tıbbi ve aromatik bir bitki olan Myrtus communis L. (Mersin) günümüzde çeşitli fitoterapötik uygulamalarda sıklıkla karşılaşılmaktadır. Bu çalışmada, Myrtus communis L. bitkisinin meyvelerinden ekstraksiyon yöntemiyle elde edilen sabit yağların verimleri hesaplanmış ve kimyasal kompozisyonu gaz kromotografisi-kütle spektroskopisi (GC-MS) ile tespit edilmiştir. En yüksek sabit yağ verimi %5.43 olarak Bursa iline ait örneklerden elde edilmiştir. Analiz sonuçlarında yağ kompozisyonu içerisinde 11 farklı bileşen tespit edilmiştir. Tüm bölgelerde en fazla bulunan yağ asitleri sırasıyla %73.97-68.96 linoleik asit (C18:2), %16.60-12.04 oleik asit (C18:1) ve %8.86-8.51 palmitik asittir (C16:0). Bu çalışmanın sonuçları Myrtus communis L. meyvesinin zengin fitokimyasal içeriği ve yüksek besleyici özelliği sayesinde gıda, tıp ve birçok farklı alanda kullanılabilirliğini ortaya koymuştur.
25 June 2022 in Business & Management Studies: An International Journal
This study's objective was to investigate lean manufacturing knowledge, awareness, and integration maturity in one of Türkiye's most significant furniture manufacturer clusters and discover the extent of tapped and untapped potential offered by lean manufacturing for the furniture industry. This study developed a survey-based data collection methodology consisting of five sections with different features. Seventy-five small to large enterprises were invited to participate in the study. Out of seventy-five, twenty-seven furniture manufacturers participated in the study. The study revealed that lean manufacturing awareness and integration maturity vary significantly. This variation could prove lean manufacturing is still far from becoming a mainstream modern management technique for members of the furniture manufacturing cluster in Bursa, Türkiye. According to 92.59% of the study participants, reducing manufacturing costs is the most common internal motivation that either triggered or has the potential to trigger lean manufacturing integration. Moreover, the amount of investment required (66.67%) to deploy lean manufacturing is the primary barrier encountered by the organizations, followed by a lack of training opportunities for workers with a percentage of 62.96%. This study was expected to serve as a valuable resource for academics and professionals intrigued by the extent of the relationship between lean manufacturing and Turkish furniture industry members.
6 February 2026 in Artvin Çoruh Üniversitesi Orman Fakültesi Dergisi
Biyobazlı ve çevre dostu ürünlere yönelik artan farkındalık, malzeme biliminde bütüncül sürdürülebilir yaklaşımların önemini ön plana çıkarmaktadır. Bu çalışmanın amacı, katma değerli bir odun dışı orman ürünü olan sülfat reçinesinin (tall oil) selüloz asetattan (SA) üretilmiş film malzemelerde doğal bir plastikleştirici olarak kullanılabilirliğini incelemektir. Farklı sülfat reçinesi katkı oranları (kütlece %10, %15, %20) ile üretilen filmler, Fourier dönüşümlü kızılötesi spektroskopisi (FTIR), mekanik analiz, termal gravimetrik analiz (TGA) ve renk analizi ile değerlendirilmiştir. FTIR bulguları, SA ve sülfat reçinesinin karakteristik fonksiyonel gruplarını doğrulamış ve sülfat reçinesi ve polimer matrisi arasındaki olası sinerjik etkileşimi vurgulamıştır. Yapıya kütlece %10 ve %15 sülfat reçinesi katkısıyla birlikte örneklerinin kopma uzama değerinin %11.46’dan %29.94’e kadar yükseldiği ve saf SA’ya göre yaklaşık iki kat arttığı gözlemlenmiştir. Termal analiz sonuçları, sülfat reçinesinin içerdiği yağ asitleri nedeniyle başlangıç bozunma sıcaklığını yaklaşık 20 °C düşürmesine rağmen, filmlerin nihai bozunma sıcaklığı üzerinde herhangi bir olumsuz etkisinin olmadığını göstermiştir. Katkı oranının artmasıyla örneklerin ΔE değerleri 10.05 ile 43,86 arasında belirgin bir şekilde artarak sarı bir renk almıştır, ancak %20’nin altındaki katkı oranlarında filmlerin hâlâ açık renk ve şeffaflığını koruduğu gözlemlenmiştir. Bu bulgular, sülfat reçinesinin çevre dostu ve sürdürülebilir bir plastikleştirici ajan olarak, endüstriyel uygulamalarda hem performans hem de çevresel fayda sağlayabileceğini göstermektedir.
2 December 2024 in Turkish Journal of Forestry | Türkiye Ormancılık Dergisi
Artan çevre sorunlarıyla birlikte, çevreye toksik etkisi daha az olan ve biyolojik olarak parçalanabilen doğal polimerlere olan ilgi her geçen gün artmaktadır. Doğal reçine, gelecek vaat eden değerli yenilenebilir bir odun dışı orman ürünü olup, birçok biyokimyasal ürünün üretilmesinde doğal bir kaynak olarak kullanılmaktadır. Bu çalışmada, yenilikçi bir polimerizasyon tekniği ile ekstraksiyon reçinesi (Crude Wood Resin), terebentin ve fenolden AlCl3 eşliğinde terpen-rosin fenolik reçine (TRFR) sentezlenmesi amaçlanmaktadır. Sentez aşamasına geçmeden önce ham reçine distilasyon ile terebentin ve kolofana ayrılmış ve gaz kromotografi - kütle spektroskopisi (GC-MS) cihazı ile karakterize edilmiştir. Sentezlenen TRFR örnekleri, Fourier Dönüşümü Kızılötesi Spektroskopisi (FTIR), Nükleer Manyetik Rezonans Spektroskopisi (NMR), asit sayısı, sabunlaşma sayısı ve yumuşama noktası analizleri ile karakterize edilmiştir. Ayrıca, sentez reaksiyonlarının modellemesi Yapay Sinir Ağı (YSA) 2 girdi (sıcaklık ve terebentin/ekstraksiyon reçine oranı) ve 4 çıktı (reaksiyon verimi, asit değeri, sabunlaşma değeri ve yumuşama noktası) ile tasarlanmıştır. En yüksek reaksiyon verimi 60°C’de üretilen, terebentin/ekstraksiyon reçine oranının 1/2 olduğu örnekte bulunmuştur. En düşük asit ve sabunlaşma değerleri sırasıyla 90,79 ve 103,79 mg KOH/g olarak hesaplanmıştır. En yüksek yumuşama noktası 79°C olarak bulunmuştur.
11 April 2026 in Journal of Innovative Science and Engineering
Polymers derived from lignocellulosic sources have gained increasing attention in recent years due to their environmental sustainability, biocompatibility, and renewability. In this study, thermal properties and water uptake behavior of cellulose acetate loaded with PEG1500 and Copernicia prunifera leaf extract were investigated. A twin-screw extruder and hot press moulding was used in the manufacturing process. An ATR-FTIR analysis was performed to identify the functional groups within the structure and to assess possible chemical changes. Thermogravimetric analysis (TGA) and Differential scanning calorimetry (DSC) analyses were performed to determine the material’s thermal properties. Subsequently, water uptake test was performed. The FTIR analysis results showed the characteristic peaks of the raw materials as expected, and no new functional groups were formed among the components. TGA results revealed that adding PEG1500 decreased the onset temperature of thermal degradation, whereas adding extract increased it by 20–30 °C. Similar behaviour was also observed in the DSC analysis, the glass transition temperature of composites increased by 5–10 °C with the addition of the extract. Additionally, its wax-like structure strengthened the hydrophobic character of the matrix by reducing its water uptake capacity. The water uptake rate of PEG-loaded cellulose acetate (w/w;10/90) decreased by 6% with the extract (5%) addition. The findings indicate that Copernicia prunifera leaf extract compensated for the negative properties of PEG1500 and was found to be suitable for use together in a cellulose acetate matrix. Using natural and biodegradable ingredients in composite systems can create an eco-friendly alternative to plastic, reducing the ecological footprint and supporting the circular economy.