In the present work, enhancement of convective heat transfer rate in three-dimensional U-shaped enclosures using nanofluids is numerically investigated. Two different types of nanoparticles, namely, Cu, and Al2O3, with pure water, are the considered single-phase nanofluids. Natural convection and geometric parameter effects on the averaged Nusselt numbers are investigated. Velocity vectors and isotherm fields for the Al2O3/H2O nanofluid are presented at various Rayleigh numbers. The governing dimensionless equations are solved using the commercial finite-volume-based computational fluid dynamics code, FLUENT. Our results are consistent with previously published predictions. In particular, heat transfer enhancement is found to increase with increasing nanoparticles volume fractions, Rayleigh numbers, as well as cooled wall length extensions.
In this paper, laminar nanofluid flow in 3D copper microchannel heat sink (MCHS) with rectangular cross section, and a constant heat flux, has been treated numerically using the computational fluid dynamics software (FLUENT). Results for the temperature and velocity distributions in the investigated MCHS are presented. In addition, experimental and numerical values are compared in terms of friction factors, convective heat transfer coefficients, wall temperature and pressure drops, for various particle volume concentrations and Reynolds numbers. The numerical results show that enhancing the heat flux has a very weak effect on the heat transfer coefficient for pure water, but an appreciable effect for the case of a nanofluid. For all considered volume fractions, the sink friction factor decreases by increasing the Reynolds number and slightly increases by increasing the volume fractions, and, with increasing the volume fractions and the Reynolds number, the pressure drop increases.
Excess properties calculated from the literature values of experimental density and viscosity in N,N-dimethylformamide (DMF) + 1,4-dioxane (DO) fluid binary mixtures (from 303.15 to 318.15) K can lead us to test the different correlation equations as well as their corresponding relative functions. Inspection of the Arrhenius activation energy Ea and the enthalpy of activation of viscous flow ∆H* shows very close values; here we can define partial molar activation energy Ea1 and Ea2 for DMF and DO, respectively, along with their individual contribution separately. Correlation between the two Arrhenius parameters of viscosity in all compositions shows the existence of the primary distinct behaviours separated by particular mole fractions in DMF. In addition, we add that the correlation between Arrhenius parameters reveals interesting Arrhenius temperature (TA), which is closely related to the vaporisation temperature in the liquid–vapour equilibrium; moreover, the limiting corresponding partial molar properties allow us to estimate the boiling points of the pure components.
23 February 2016 in Physics and Chemistry of Liquids
In the present study, the natural convective heat transfer in a cube filled with Al2O3/H2O and Ag/H2O nanofluids is investigated numerically. Commercial CFD code FLUENT has been used to simulate water-based nanofluid considering it as a single-phase fluid. The influence of different parameters, such as the Rayleigh number and the nanoparticle volume fraction, is studied. The velocity vectors and the isotherm profiles are plotted. The variation of the Average Nusselt number at the hot wall and the variation of y-component of velocity are presented and discussed. The numerical results show a decrease in the heat transfer with the increase in the particle volume fraction and the same trend in the increase of the Nusselt number with the Rayleigh number.
21 September 2016 in Physics and Chemistry of Liquids
Calculation of excess properties in 1,2-dimethoxyethane (DME) + propylene carbonate (PPC) binary liquid mixtures at (298.15, 308.15 and 318.15) K from experimental viscosity and density values was presented in earlier work. Investigations of these experimental values to test correlation quality of different equations as well as their corresponding relative functions were also reported. Considering the quasi-equality between the enthalpy of activation of viscous flow ΔH* and the viscosity Arrhenius activation energy Ea, here, we can define partial molar activation energy and for DME with PPC, respectively, along with their individual contribution separately. Correlation between Arrhenius parameters brings to light interesting Arrhenius temperature with a comparison to the temperature of vaporisation in the liquid vapour equilibrium, and the limiting corresponding partial molar properties that can permit us to predict value of the boiling points of the pure components. New empirical equations for estimating the boiling temperature are proposed.