5 August 2022 in IEEE Transactions on Circuits and Systems II: Express Briefs
This brief presents a 2.0 42.0 GHz ultra-wide bandwidth Cascode distributed low-noise amplifier (CDLNA) MMIC design. With the proposed coupled-line (CL) sections between each drain-artificial transmission line (D-ATML) node and related gate-artificial transmission line (G-ATML) node, the traveling signal is reused to enhance the gain and broaden the operation bandwidth simultaneously. To improve the gain further, the inductive gain peaking has also been employed at each drain of common-source (CS) and common-gate (CG) transistors. Meanwhile, an active termination technique incorporating active and passive elements has been adopted to achieve better noise figure (NF) performance. Employing the proposed techniques, an LNA prototype has been designed and fabricated in a 0.15-μm GaAs E-Mode pHEMT technology with the chip size of 1.53 mm including all the pads. From test results, the proposed CDLNA demonstrates a peak gain of 14.1 dB, the best NF of 2.1 dB, a group delay of 102±58.4 ps, and 23.25/14.7 dBm best OIP3/OP1dB, respectively. The total power consumption is 129 mW under 3 V VDD.
25 January 2023 in IEEE Transactions on Circuits and Systems I: Regular Papers
In this paper, a 2-stage compact wideband low-noise amplifier (LNA) monolithic microwave integrated circuit (MMIC) with multiple resistive feedback (MRFB) is presented. From the DC point of view, the proposed MRFB functions as a self-biasing structure to bias transistors in the optimal condition, improving the noise figure (NF) and linearity. Meanwhile, by employing MRFB with source degeneration and input inductor, the proposed LNA achieves wideband flat gain at the AC side. In comparison with traditional topologies, a wide bandwidth of more than 11.5 GHz with low noise figure of less than 2.5 dB can be achieved. To verify the proposed LNA structure, a chip prototype is fabricated in a 0.15- $\mu$ m GaAs E-mode pHEMT process with a compact die size of only 0.75 mm $^2$ including all the testing pads. From the measurement results, the proposed LNA circuit features a 1.0 to 12.5 GHz 3-dB working bandwidth (172% fractional bandwidth), 23.6 peak gain, 1.51 dB minimum NF, 66.7 $\pm$ 15 ps group delay, and 24.3/12.6 dBm best OIP3/OP1dB, respectively. The total DC power is around 87.5 mW from a single 2.5-V power supply.
26 September 2022 in IEEE Transactions on Microwave Theory and Techniques
A neural network (NN)-based hybrid physical model for gallium nitride high-electron-mobility transistors (GaN HEMTs) is proposed. In this model, the artificial NN (ANN) is used to construct the terminal charge densities, which is linked with device model’s RF and dc performance using the MIT Virtual Source (MVS) theory. A detailed parameter extraction and optimization method for this hybrid model is proposed as well. The parameter extraction starts from S-parameters with the consideration of access region resistances. The particle swarm optimization (PSO) is used to optimize extraction results. After that, a two-hidden-layer ANN is constructed to model the obtained source-end terminal charge density ( $q_{\mathrm{is}})$ and drain-end terminal charge density ( $q_{\mathrm{id}})$ . Then, the ANN-based $q_{\mathrm{is}}$ and $q_{\mathrm{id}}$ are used to construct the hybrid model under the framework of the MVS theory. The trapping effects and self-heating effects are also considered in this hybrid model. This hybrid model is built and verified in the Advanced Design System (ADS). The proposed hybrid model has better scalability than the traditional ANN-based models. It is also more accurate than the traditional MVS-based physical model. This hybrid model presents satisfactory agreement between measured and simulated current–voltage (IV), S-parameters, load—pulls, and power sweeps.
26 January 2023 in IEEE Transactions on Circuits and Systems I: Regular Papers
This article presents a 3-stage millimeter-wave low-noise amplifier (LNA) monolithic microwave integrated circuit (MMIC) design for broadband applications. The proposed structure consists of cascading common-source (CS) LNA with coupled interstage feedback (CIF) paths at the second and third stages. By tuning the coupling factor and the inductance of the CIF, enhanced overall gain and extended working bandwidth can be achieved simultaneously. The proposed CIF formed by a simple on-chip edge-coupled parallel metal-lines features small size and high flexibility. To facilitate circuit design and optimization, an equivalent circuit for the proposed CIF structure is developed. Besides, to address the trade-off between impedance matching and noise performance, a noise matching strategy focusing more on higher frequencies is presented to achieve good noise performance. With the proposed techniques, an LNA prototype is demonstrated in a commercial 0.15- $\mu$ m GaAs E-mode pHEMT process. The fabricated LNA has a die size of 1.15 mm $^2$ and DC power consumption of 109 mW. The measurement results show a peak gain of 25.6 dB with a 3-dB bandwidth of 9 $\sim$ 42 GHz, the minimal noise figure (NF) of 1.91 dB, a group delay of 68.7 $\pm$ 20.5 ps, and 20.8 dBm best OIP3 under 2.0-V VDD.
11 May 2021 in IEEE Transactions on Microwave Theory and Techniques
Neural network-based capacitance models are accurate, but some of them are not charge-conservative. In this work, a novel consistent gate charge model for GaN high electron mobility transistors is presented based on neural networks. The equivalent circuit parameters are extracted using the multiobjective gray wolf optimizer-based hybrid method, which improves the accuracy of parameter extraction. To obtain more reliable data sets for accurate neural network-based modeling, the outliers in the extracted intrinsic capacitances are automatically detected and removed using the isolation forest technique. The gate charge is obtained by integrating the capacitances with the voltages at different temperatures. A neural network is used to model the bias- and temperature-dependent gate charges, and the intrinsic capacitance formulation is obtained by taking the partial derivative of the gate charge function with respect to the voltages. The proposed model is charge-conservative and requires no transcapacitances. The large-signal model is implemented in the Advanced Design System and verified by small- and large-signal measurements. Good agreement is obtained between the measurements and simulations.
28 July 2022 in IEEE Microwave and Wireless Components Letters
In this letter, a 10–43-GHz low-noise amplifier (LNA) monolithic microwave integrated circuit (MMIC) is designed in a commercial 0.15- $\mu$ m GaAs E-mode pseudomorphic high electron mobility transistor (pHEMT) technology. In the proposed LNA circuit, a novel coupled-line (CL)-based positive feedback structure is employed with the bandpass characteristic. By carefully tuning its coupling factor and arm length, the center frequency $f_c$ and the intensity of the feedback can be controlled, respectively. Subsequently, targeting $f_c$ at the higher cutting edge of the working band leads to compensated gain roll-off and extended bandwidth. Incorporating three-stage common-source (CS) architectures, an LNA prototype is fabricated with a size of 1.05 mm $^2$ including pads. Under 2-V voltage drain drain (VDD), good performance is obtained, including 24.6-dB peak gain with 3-dB bandwidth of 33 GHz, 2.4–3.0-dB noise figure (NF), 54.5 $\pm$ 13.8-ps group delay, and 12.3/21.5-dBm best output power at 1 dB gain compression (OP1dB)/output third order intercept point (OIP3). The total dc power is 110 mW.