13 February 2006 in Applied Physics Letters
Nanocarbon-doped Fe-sheathed MgB2 tapes with different doping levels were prepared by the in situ powder-in-tube method. Compared to the undoped tapes, Jc for all the C-doped samples was enhanced by more than an order of magnitude in magnetic fields above 9T. At 4.2K, the transport Jc for the 5at.% doped tapes reached 1.85×104A∕cm2 at 10T and 2.8×103A∕cm2 at 14T, respectively. Moreover, the critical temperature for the doped tapes decreased slightly. Transmission electron microscopy showed a number of intragranular dislocations and the dispersed nanoparticles embedded within MgB2 grains induced by the C doping. The mechanism for the enhancement of flux pinning is also discussed. These results indicate that powder-in-tube-processed MgB2 tape is very promising for high-field applications.
1 July 2015 in Journal of Magnetic Resonance
1 January 2010 in Physica C: Superconductivity and its Applications
30 April 2021 in Superconductor Science and Technology
This paper presents experimental results on a quench of an intra-layer no-insulation (LNI) (RE: rare earth)Ba2Cu3O7−δ
(REBCO) coil in a 31.4 T central magnetic field and simulated results on the quench. We have been designing a persistent-mode 1.3 GHz (30.5 T) nuclear magnetic resonance (NMR) magnet with a layer-wound REBCO inner coil. Protection of the REBCO coil from quench is a significant issue and the coil employs the LNI method to obtain self-protecting characteristics. We conducted high-field generation and quench experiments on an LNI-REBCO coil connected to an insulated Bi2Sr2Ca2Cu3O
x
(Bi-2223) coil under a background magnetic field of 17.2 T as a model of the 1.3 GHz NMR magnet. The coils successfully generated a central magnetic field of 31.4 T. Although the LNI-REBCO coil quenched at 31.4 T, this quench did not cause any degradation to the coil. A numerical simulation showed the current distribution during the quench was non-uniform and changed rapidly over time due to current bypassing through copper sheets between layers, resulting in faster quench propagation than in an insulated REBCO coil. During the quench propagation, the peak temperature (T peak) and the peak hoop stress BzJR (σθ,
peak) were calculated to be 330 K and 718 MPa, respectively. These are below critical values that cause degradation. The simulation also showed that the high electrical contact resistivity (ρ ct) of 10 000 µΩ cm2, between REBCO conductors and copper sheets in the LNI-REBCO coil winding, played an important role in protection. When ρ ct was as low as 70 µΩ cm2, the quench propagation became too fast and large additional currents were induced, resulting in an extremely high σθ,
peak of 1398 MPa, while the T peak was as low as 75 K. In short, the high ρ ct in the present coil caused a high T peak, but succeeded in suppressing σθ,
peak and protecting the coil from the quench.
7 January 2016 in IEEE Transactions on Applied Superconductivity
This paper presents the results of a high field generation test for layer-wound HTS coils in a background magnetic field. The test revealed new types of degradation for a REBCO coil caused by an electromagnetic force. A series-connected REBCO coil and a Bi-2223 coil were charged at 4.2 K in a background magnetic field of 17.2 T to generate a central magnetic field of 28.2 T (nuclear-magnetic-resonace frequency of 1.2 GHz). However, a premature normal voltage appeared on the REBCO coil, and the charging was stopped at 25 T. Unwinding the REBCO coil after the experiment found: 1) delamination, due to a cleavage and peeling, of the conductor in a soldered joint inside the winding; and 2) axial movement and edgewise bend deformation of the REBCO conductor at the outermost layer. The keyword of the present degradation is stress concentration, which is also the origin of the more widely known thermal stress-induced degradation.
1 May 2001 in Nuclear Fusion