Yu Li

Yu Li

Auto-generated profile, based on publicly available information

Yu Li

School of Metallurgy Northeastern University Shenyang 110819 Liaoning China

Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 September 2025 in Steel Research International
Verified
Journal Article
Closed access
HCHuan Cao
Huan Cao
WYWenbin Yang
Wenbin Yang
YLYu Li
Yu Li
XHXuechi Huang
Xuechi Huang
ZLZHongqiu Liu
ZHongqiu Liu
BLBaokuan Li
Baokuan Li

1 January 2025 in Physics of Fluids
Verified
Journal Article
Closed access
YLYu Li
Yu Li
ZLZHongqiu Liu
ZHongqiu Liu
YXYongtao Xiong
Yongtao Xiong
YYYuchao Yao
Yuchao Yao
BLBaokuan Li
Baokuan Li
GXGuodong Xu
Guodong Xu
This study employs computational fluid dynamics (CFD) coupled with the population balance model (PBM) to explore the sensitivity of the drag model for the predictive accuracy of the gas–liquid two-phase flow in continuous casting (CC) mold. Several single bubble drag models have been numerically evaluated for high turbulent intensity and gas flow rate operation parameters. Then, the influence of turbulence effect and bubble swarm mechanisms on bubble dynamic behaviors are investigated. The predicted mean bubble diameter and flow pattern were studied and compared with the experimental data. The results show that all single bubble drag models, except for the Grace model, can predict the bubble size distribution (BSD) well. Meanwhile, all models significantly overestimate the bubble diameter near the nozzle under high gas flow rate conditions. A novel drag correction factor based on local gas holdup and BSD is proposed, which takes into account both the hindrance effect of small bubbles and the accelerating effect of large bubbles. The proposed drag correction factor can accurately predict BSD and flow pattern transition in the CC mold under high gas holdup regions. Compared with the simulation results of the previous single bubble drag model, the mean relative error predicted by the novel drag correction factor is decreased by 69.33%.

1 August 2025 in Physics of Fluids
Verified
Journal Article
Closed access
ZLZHongqiu Liu
ZHongqiu Liu
YLYu Li
Yu Li
YYYuchao Yao
Yuchao Yao
NWNing Wang
Ning Wang
SLShaodan Li
Shaodan Li
BLBaokuan Li
Baokuan Li
The dispersed bubbly flow dramatically changes the shear-induced turbulence (SIT) in gas–liquid systems. Modifications to the liquid turbulence model by adding source terms or a bubble-induced turbulence (BIT) viscosity term can improve the accuracy of numerical simulation. However, there is no consensus on the definition of the characteristic time scale of turbulent eddies induced by bubbles, which directly relates to the modeling work of the BIT source. We compared the effects of different character time scale models on multi-scale bubbly flow and developed a novel BIT model based on the gas-phase intrinsic turbulence parameters. Then, the coupling mechanism between SIT and BIT models was revealed. The results show that the population balance and Sato models show better consistency than other models for simulating bubble diameter and flow regimes. The bubble response time significantly underestimates the characteristic time, thereby enhancing the collision frequency between bubbles. A novel mixture BIT model is proposed based on the turbulent properties of gas and liquid phases. Compared with the numerical simulation of the without BIT model, the mean relative error predicted by the novel BIT is reduced by 45.28%. Finally, introducing the BIT viscosity model and the smallest eddy dissipation time model forms a positive feedback loop between BIT and liquid-phase SIT, thereby enhancing turbulent dispersion. However, an anomalous negative feedback loop mechanism was formed between BIT and SIT when using the bubble response time model.

1 June 2025 in Physics of Fluids
Verified
Journal Article
Closed access
NWNing Wang
Ning Wang
ZLZHongqiu Liu
ZHongqiu Liu
YYYuchao Yao
Yuchao Yao
YXYongtao Xiong
Yongtao Xiong
YLYu Li
Yu Li
BLBaokuan Li
Baokuan Li
Ladle plug clogging, a widespread challenge in ladle refining, profoundly influences various stages of the process. However, existing numerical simulations and water model experiments primarily assume an idealized non-clogging condition, posing a significant constraint on the comprehensive understanding and optimization of refining operations. This study comprehensively investigates the impact of porous plugs on refining efficiency under various clogging conditions, with a focus on gas–liquid flow, mixing time, and slag eye behavior to establish a full-size three-dimensional mathematical model of 135 t ladle and offers practical solutions to mitigate the negative effects. A 1:4 water model experiments were carried out to verify the accuracy of mathematical models. The results indicate that plug clogging influences refining efficiency by altering the initial bubble characteristics. As the degree of clogging increases, the initial bubble diameter distribution shifts toward larger diameters. The overall stirring energy is reduced by approximate 10%, and the axial velocity in the slag-molten steel interface and bubble plume area is significantly reduced. At flow rates of 300 and 450 NL/min, mixing time exhibits a positive correlation with the degree of clogging. However, when the flow rate increases to 600 NL/min, mixing time fluctuates unpredictably with clogging severity. When the initial flow rates are 300 and 450 NL/min, following clogging, increasing the flow rate to 600 NL/min may offset the negative impact of congestion on mixing time. Post-clogging, the slag eye area decreases by up to 18%, and the instability in slag eye fluctuation increases with higher clogging severity. This mathematical model can also be employed to investigate the clogging issues of slot-type plugs.

1 February 2026 in Physics of Fluids
Verified
Journal Article
Closed access
YYYuchao Yao
Yuchao Yao
ZLZHongqiu Liu
ZHongqiu Liu
QYQianru Yang
Qianru Yang
NWNing Wang
Ning Wang
YLYu Li
Yu Li
BLBaokuan Li
Baokuan Li
Feeding a strip into the mold has a positive effect on improving the homogeneity of a large continuous casting bloom. A visualized solidification experimental system was established to investigate the solidification and flow behavior in the mushy zone and melt under conditions without strip and strip feeding. Results show that the rejection and flow of the lighter water-rich solutions form channels in the mushy zone and cause stratification in the melt. The crystal agglomeration of equiaxed crystals produced by dendrite remelting is observed at the top corner of the mold. After strip feeding, the dendrites on the surface and inside the cold strip are remelted into free-moving equiaxed crystals. The counterclockwise flow is changed into a smaller flow and a clockwise axe-shaped flow, and the maximum velocity increases from 1.38 mm/s without strip to 5.25 mm/s after strip feeding. The equiaxed crystals are transported by both the counterclockwise flow and the axe-shaped flow before settling to the mold bottom. The volume fractions of equiaxed crystals in the solidification structure are 19% and 31% under the conditions without strip and strip feeding. The mathematical relationships between the volume fraction of solidification structure and time are established.