School of Biomedical Engineering, Colorado State University, Fort Collins, CO, 80523, USA; Department of Chemical and Biological Engineering, Colorado State University, Fort Collins, CO, 80523, USA
Auto-generated profile, based on publicly available information
David S. Dandy
School of Biomedical Engineering, Colorado State University, Fort Collins, CO, 80523, USA; Department of Chemical and Biological Engineering, Colorado State University, Fort Collins, CO, 80523, USA
Three-dimensional numerical solutions have been obtained for steady, linear shear flow past a fixed, heated spherical particle over a wide range of Reynolds number (0.1 [les ] R [les ] 100) and dimensionless shear rates (0.005 [les ] α [les ] 0.4). The results indicate that at a fixed shear rate, the dimensionless lift coefficient is approximately constant over a wide range of intermediate Reynolds numbers, and the drag coefficient also remains constant when normalized by the known values of drag for a sphere in uniform flow. At lower values of the Reynolds number, the lift and drag coefficients increase sharply with decreasing R, with the lift coefficient being directly proportional to R−½. For the range of shear rates studied here, the rate of heat transfer to the particle surface was found to depend only on the Reynolds number, that is, it was insensitive to the shear rate. The dimensionless rate of heat transfer, the Nussel number Nu, was seen to increase monotonically with R.
The growth of diamond in a subatmospheric dc‐arc plasma‐jet reactor has been studied theoretically. Full transport equations for this geometry, including gas‐phase and surface chemistry, have been solved numerically. The surface‐reaction mechanism includes pathways for the incorporation of CH3, C2H2, and C from the gas phase, as well as growth of graphite. The surface mechanism includes full reversibility for all reactions, based on estimates of the thermochemistry. Results are presented for degrees of dissociation of H2 in the plasma gun ranging from 2.6% to 90%, and inlet levels of CH4 spanning 0.1–5.0 mol %. It is seen that CH3 is the predominant growth species when there is little H2 dissociation within the plasma gun, but C becomes the dominant species at higher dissociation levels. The third growth species, C2H2, does not play a role in diamond growth under these conditions when there is less than 1% CH4 in the feed; but, at higher CH4 levels both C and CH3 addition rates drop to 50 times greater than C2H2.
Numerical solutions have been obtained for steady streaming flow past an axisymmetric drop over a wide range of Reynolds numbers (0.005 [les ] Re [les ] 250), Weber numbers (0.005 [les ] We [les ] 14), viscosity ratios (0.001 [les ] λ [les ] 1000), and density ratios (0.001 [les ] ζ [les ] 1000). Our results indicate that at lower Reynolds numbers the shape of the drop tends toward a spherical cap with increasing We, but at higher Re the body becomes more disk shaped with increasing We. Unlike the recirculating wake behind an inviscid bubble or solid particle, the eddy behind a drop is detached from the interface. The size of the eddy and the separation distance from the drop depend on the four dimensionless parameters of the problem. The motion of the fluid inside the drop appears to control the behaviour of the external flow near the body, and even for cases when λ and ζ [Lt ] 1 (a ‘real’ bubble), a recirculating wake remains unattached.
Multilayer paper devices are used to generate fast flow rates (1.56 cm s −1 ) which are 145-fold quicker than classical single-layer paper device designs. These self-pumping devices are demonstrated for the sequential injection stripping analysis of cadmium.
Controlled pumping of fluids through microfluidic networks is a critical unit operation ubiquitous to lab-on-a-chip applications. Although there have been a number of studies involving the creation of passive flows within lab-on-a-chip devices, none has shown the ability to create temporally stable flows for periods longer than several minutes. Here a passive pumping approach is presented in which a large pressure differential arising from a small, curved meniscus situated along the bottom corners of an outlet reservoir serves to drive fluid through a microfluidic network. The system quickly reaches steady-state and is able to provide precise volumetric flow rates for periods lasting over an hour. A two-step mathematical model provides accurate predictions of fluid and mass transport dynamics in these devices, as validated by particle tracking in laboratory systems. Precise flow rates spanning an order of magnitude are accomplished via control of the microchannel and outlet reservoir dimensions. This flow mechanism has the potential to be applied to many micro-total analytical system devices that utilize pressure-driven flow; as an illustrative example, the pumping technique is applied for the passive generation of temporally stable chemical gradients.