16 August 2013 in IEEE Communications Magazine
A body area network is a radio communication protocol for short-range, low-power, and highly reliable wireless communication for use on the surface, inside, or in the peripheral proximity of the human body. Combined with various biomedical sensors, BANs enable realtime collection and monitoring of physiological signals. Therefore, it is regarded as an important technology for the treatment and prevention of chronic diseases, and health monitoring of the elderly. The IEEE 802 LAN/MAN Standards Committee approved Task Group TG15.6 in December 2007. As a result of more than four years of effort, in February 2012, TG15.6 published the first international standard for BANs, IEEE Std 802.15.6. Throughout the development of this standard, ample collaboration between the standardization group and the research community was required. In particular, understanding the radio propagation mechanisms for BANs demanded the most research effort. Technical challenges were magnified for the case of implant communication because of the impossibility of conducting in-body measurements with human subjects. Therefore, research in this field had to make use of intricate computer simulations. This article outlines some of the research that has been done to obtain accurate propagation models supporting the standardization of implant communication in BANs. Current research to enhance the channel models of IEEE Std 802.15.6 through the use of ultra wideband signals for implantable devices along with physical measurements in animals is also presented.
9 December 2011 in IET Microwaves, Antennas & Propagation
Implant medical wireless sensors for monitoring physiological parameters, automatic drug provision, and so on represent a new promising healthcare technology. Inherent characteristics of ultra-wideband (UWB) radio make this technology highly suitable for the wireless interface of implant sensors. A communication channel model is essential for developing these wireless systems. However, there are currently few models describing the radio propagation inside the human body. To address this problem, a statistical model is presented for UWB propagation channels inside the human chest in the 1–6 GHz frequency range. The proposed statistical model is developed from numerical simulations using a heterogeneous anatomical model that includes the frequency-dependent dielectric properties of different human tissues. Mathematical formulas for the computation of path loss, scattering and the statistical implementation of the channel impulse response at different depths inside the chest are described. Two typical depths for implanted sensors in the chest, namely 20 and 80 mm are analysed in detail. Average path loss of approximately 20 and 50 dB is observed in each case, respectively. Moreover, the channel exhibits little time dispersion with a root-mean-square delay spread below 1 ns in both cases. These results aim at facilitating the tasks associated with the design of in-body medical communication systems.
29 April 2014 in IEEE Antennas and Wireless Propagation Letters
A broadband single-layer reflectarray antenna composed of multiresonance square-rings elements is presented. The element is optimized to provide a linear phase curve and wide-enough phase variation. To avoid feed blockage, an offset feed configuration is used, and wave incident angle is considered to determine the appropriate element parameters that provide desirable phase shift on the antenna surface. The aperture efficiency of the antenna is maximized by optimizing feed position and characteristics. A 480-element antenna is fabricated and measured. The measured results show 1-dB gain bandwidth of 17% and radiation efficiency of 66% at 13.5 GHz center frequency.
21 March 2009 in IEEE Transactions on Antennas and Propagation
New design of a single feed reconfigurable circular patch antenna with polarization pattern diversity is presented. The radiating circular patch, printed on a thin substrate, is supported by non conductive posts on a conducting ground plane and is excited with a capacitively coupled feed. Wideband impedance matching is achieved. The pattern diversity is generated using two switch parasitic pins between the circular patch and the ground plane. By optimizing the position of the switching elements, two orthogonal patterns with the right-hand circular polarization (RHCP) and the left-hand circular polarization (LHCP) are generated. These patterns are used for diversity reception in indoor fading channel for wireless LAN applications. Detailed design of the antenna is described. Experimental results for return loss, radiation patterns, radiation efficiency, antenna gain, axial ratio and the diversity performance in Rayleigh fading channel are presented.
18 October 2013 in IEEE Transactions on Components, Packaging and Manufacturing Technology
MSMilad Sharifi Sorkherizi
This paper describes a novel design for a direct-coupled cavity filter realization using a ridge gap waveguide technology. A ridge gap waveguide transmission line with two coaxial feed connectors is designed and operated within the frequency band of 10-13 GHz. A cavity is coupled to the transmission line to achieve bandstop filter characteristic. Then, the structure of the filter is modified in a way to generate a bandpass feature. The final manufactured prototype is a fourth-order bandpass filter, operating at the center frequency of 11.59 GHz with a bandwidth of 72 MHz. The proposed design has potential applications in channeling filters for telecommunication satellites.
12 March 2007 in IEEE Transactions on Antennas and Propagation
A printed meander line antenna is described with a shaped ground plane and a back coupled rectangular patch. The prototype is proposed for wireless local-area network (WLAN) applications in the 2.4-2.48GHz and 5.15-5.35 GHz frequency range. Dual-band operation, resonance impedance matching, and wide impedance bandwidth are the characteristics of the antenna. The antenna impedance matching for the first-resonance is provided by applying a shaped ground plane. The second even-mode resonance is generated by adding a rectangular patch at the back of the meander antenna. The impedance bandwidth for a return-loss less than -10 dB is 11% and 6% for the first- and the second-resonance, respectively. Furthermore, the second-resonance frequency can be tuned by the length of the rectangular patch and it meets the requirements for the IEEE 802.11a WLAN (5.15-5.35 GHz and 5.470-5.725 GHz or 5.725-5.825GHz). In fact, the second-resonance frequency can be continuously adjusted between 5.2 and 7 GHz with a little effect on the first-resonance